What are two commands that can be used to configure MBGP for multicast?()
第1题:
A. set protocols isis inet6
B. set routing-options router-id router-id
C. set protocols ospf3 area 0 interface all
D. set interface fe-0/0/1 unit 0 family inet6
E. set routing-options ipv6-router-id router-id
第2题:
A. router bgp 100 neighbor 192.168.10.1 remote-as 200 address-family ipv4 multicast neighbor 192.168.10.1 next-hop-self
B. router bgp 100 neighbor 192.168.10.1 remote-as 200 address-family vpnv4 multicast neighbor 192.168.10.1 activate
C. router bgp 100 neighbor 192.168.10.1 remote-as 200 address-family ipv4 unicast neighbor 192.168.10.1 active
D. router bgp 100 neighbor 192.168.10.1 remote-as 200 address-family ipv4 multicast neighbor 192.168.10.1 activate
第3题:
You are the network administrator responsible for testing and deploying new service packs for Windows 2000. Your forest has two trees, with four domains in each tree, as shown in the exhibit.
For the testing of each service pack, you plan to deploy the service pack to the support.IS.contoso.com domain and the support.IS.litware.com domain, but to no other domains. You plan to use a Group Policy to configure and administer the service pack package. You need to minimize the complexity and administration of the service pack package, and to minimize network traffic between the domains.
You create a Microsoft Windows Installer package for the service pack. What should you do to configure the Group Policy?
A.Configure the Windows Installer package in a Group Policy for the litware.com and contoso.com domains
B.Configure the Windows Installer package in a Group Policy for the support.IS.litware.com and support.IS.contoso.com domains.
C.Configure two sites, with one tree in each site. Configure the Windows Installer package in a Group Policy for each site.
D.Configure one site that contains both trees. Configure the Windows Installer package in a Group Policy for the site.
第4题:
Which two functions can be configured on the ERX Edge Router to support MBGP? ()(Choose two.)
第5题:
A. Configure the net system - id command under routerisis and enable IS - IS on each interface with the ip router isis command.
B. Configure the net sy stem - id and the network net - id commands under routerisis.
C. Configure the network net - id command(s) under routerisis and enable IS - IS on each interface with the ip router isis command.
D. Configure the network net - id command(s) and the is - type level -1- 2 command under routerisis.
E. Configure the net system - id and the network net - id commands under routerisis and enable ISIS on each interface with the ip router isis command.
第6题:
A. inet.0
B. inet.1
C. inet.2
D. inet.4
第7题:
A. Under the BGP group, configure family inet any.
B. Use the set protocol MBGP command to enable MBGP.
C. Under the BGP group, configure family inet multicast.
D. Use the set rib-group command to copy the multicast routes into inet.1.
第8题:
A network administrator repeatedly receives support calls about network issues. After investigating the issues, the administrator finds that the source NAT pool is running out of addresses.To be notified that the pool is close to exhaustion, what should the administrator configure?()
A. Use the pool-utilization-alarm raise-threshold under the security nat source stanza.
B. Use a trap-group with a category of services under the SNMP stanza.
C. Use an external script that will run a show command on the SRX Series device to see when the pool is close to exhaustion.
D. Configure a syslog message to trigger a notification when the pool is close to exhaustion.
第9题:
You wish to configure IPv6 support on a router which does not have any current IPv4 configuration.Which three steps are used to configure IPv6 with an accompanying IGP in JUNOS software? ()
第10题:
What are two commands that can be used to configure MBGP for multicast?()