配置CISCO7600以太端口为Trunk模式的命令是()
第1题:
阅读下面的配置信息,解释(7)处的命令。
Switchconfig t
Switch(eonfig)interface f0/5(进入端口5的配置模式)
Switch(config-if)switchport mode access(7)
Switch(config-if)switchport access vlan 2(把端口5分配给相信的VLAN2)
Switch(config-if)exit
Switch(config)interface f0/6
Switch(config-if)switchport mode access
Switch(config-if)switchport access vlan 3
Switch(config-if)exit
Switch(config)exit
Switch
第2题:
以下哪个命令用于创建一个trunk?
A、switchport mode trunk
B、switchport trunk enable
C、switchport trunk
D、trunk enable
A.
B.
C.
D.
第3题:
如下图所示,3com和Cisco公司的交换机相互连接,在两台交换机之间需传输ULANID为1、10、20和30的4个VLAN信息,Catalyst 3548交换机VLAN Trunk的正确配置是
A.Switch-3548 (config-if) #switchport trunk encapsulation dot 1 q Switch-3548 (config-if) #switchport trunk allowed vlan 1,10,20,30
B.Switch-3548 (config-if) #switchport mode trunk Switch-3548 (config-if) #switchport trunk encapsulation isl Switch-3548 (config-if) #switchport trunk allowed vlan 1-30
C.Switch-3548 (config-if) #switchport mode trunk Switch-3548 (config-if) #switchport trunk encapsulation negotiate Switch-3548 (config-if) #switchport trunk allowed vlan 1-30
D.Switch-3548 (config-if) #switchport mode trunk Switch-3548 (config-if) #switchport trunk encapsulation dot 1q Switch-3548 (config-if) #switchport trunk allowed vlan 1,10,20,30
第4题:
此题为判断题(对,错)。
第5题:
A、Switch(config-if)#switchport mode access
B、Switch(config-if)#switchport dynamic auto
C、Switch(config-if)#switchport mode trunk
D、Switch(config-if)#switchport mode dynamic
第6题:
阅读以下说明和交换机的配置信息,回答问题1~3,将解答填入对应栏内。
某公司下设3个部门,为了便于管理,每个部门组成一个VLAN,公司网络结构如图1所示。
[交换机Switch1的部分配置信息]
Switch1(config)tinterface fO/9
Switch1(config-if)switchport mode access
Switch1(config-if)switchport access vlan 11
Switch1(config)interface fO/10
Switch1(config-if)switchport mode access
Switch1(config-if)switchport access vlan 12
Switch1(config)interface fO/17
Switch1(config-if)switchport mode access
Switch1(config-if)switchport access vlan 13
[交换机Switch2的部分配置信息]
Switch2(config)interface fO/6
Switch2(config-if)switchport mode access
Switch2(config-if)switchport access vlan 11
Switch2(config)interface fO/8
Switch2(config-if)switchport modeaccess
Switch2(config-if)switchport access vlan 12
Switch2(config)interface fO/11
Switch2(config-if)switchport mode access
Switch2(config-if)SWitchport access vlan 13
[交换机Switch3的部分配置信息]
Switch3(config)interface fO/3
Switch3(config-if)switchport mode access
Switch3(config-if)switchport access vlan 11
Switch3(config-if)exit
Switch3(config)interface fO/7
Switch3(config-if)switchport mode access
Switch3(config-if)switchport access vlan 12
Switch3(config)interface fO/13
Switch3(config-if)switchport mode access
Switch3(config-if)switchport aocess vlan 13
划分VLAN有哪几种划分方式?
第7题:
A、switchport mode access
B、switchport mode dynamic desirable
C、switchport mode auto
D、switchport nonegotiate
第8题:
You need to configure an 802.1Q link on a Ezonexam switch. Which commands, when used together, would do this? (Select two answer choices)
A. Switch(vlan) mode trunk
B. Switch(config) switchport access mode trunk
C. Switch(config-if) switchport mode trunk
D. Switch(config-if) switchport trunk encapsulation dot1q
E. Switch(config) switchport access mode 1
F. Switch(vlan) trunk encapsulation dot1q
第9题:
A、Switchport mode access
B、Switchport mode trunk
C、Switchport mode dynamic auto
D、Switchport mode dynamic desirable
第10题:
A. Switch(vlan)# mode trunk
B. Switch(config)# switchport access mode trunk
C. Switch(config-if)# switchport mode trunk
D. Switch(config-if)# switchport trunk encapsulation dot1q
E. Switch(config)# switchport access mode 1
F. Switch(vlan)# trunk encapsulation dot1q