What is the correct command to set the router ID for an OSPF

A. The LSA was created by an ABR due to an area range command.

B. The LSA was created by an ASBR due to a summary - address command.

C. If cr eated by an area range command, the best metric for a subordinate subnet on that ABR must have been 11.

D. None of the other answers is correct.

A. It is used with the OSPF priority values to determine which OSPF router will become the DR or BOR in a point-to-point network

B. It is used with the OSPF priority values to determine which interface will be used to form a neighbor relationship with another OSPF router

C. It is used with the OSPF priority values to determine which router will become the DR or BOR in a multi access network

D. It is used to determine which interfaces will send Hello packets to neighboring OSPF routers

A. set protocols isis inet6

B. set routing-options router-id router-id

C. set protocols ospf3 area 0 interface all

D. set interface fe-0/0/1 unit 0 family inet6

E. set routing-options ipv6-router-id router-id

OSPF is configured over a Frame Relay network as shown in the exhibit. All PVCs are active.However, R1 and R3 fail to see all OSPF routes in their routing tables. The show ip ospf neighbor command executed on R2 shows the state of t he neighbors. What should be done to fix the problem? （）

A. The ip ospf network broadcast command should be configured on each Frame Relay interface

B. The ip ospf network non -broadcast command should be configured on each Frame Relay interface

C. Th e ip ospf priority value on the spoke routers should be set to 0

D. The ip ospf priority value on the hub router should be set to 0

E. The neighbor command should be configured under the OSPF routing process on all routers

A. router ospf ipv6 process - id

B. ipv6 ospf process - id

C. router ospf process - id

D. ipv6 router ospf process - id

You have implemented mutua l route redistribution between OSPF and EIGRP on a border router. When checking the routing table on one of the EIGRP routers within the EIGRP routing domain, you are seeing some, but not all of the expected routes.What should you verify to troubleshoot this problem?（）

A. The border router is using a proper seed metric for OSPF

B. The border router is using a proper seed metric for EIGRP

C. The administrative distance is set for OSPF and EIGRP

D. The missing OSPF routes are present in the routing table of the border router

E. The subnet keyword on the border router in the redistribute OSPF command

Refer to the exhibit. You have completed an OSPF implementation, and you are verifying OSPF operation. You notice that router A and router B are stuck in the two - way state. From the show ip ospf interface command output, what is the cause of this issue?（）

A. All OSPF implementations must have at le ast one interface in area 0.

B. You are attempting to run in the broadcast mode over an NBMA interface.

C. Both routers are configured to function as a BDR; therefore, there is no DR router.

D. Someone has changed the OSPF router ID; therefore you must clear the OSPF process.

E. The OSPF priority is set to 0 on both routers; therefore neither can become the DR.

A.

B.

C.

D.

A. Ensure that an interface has been configured with an IP address

B. Ensure that IP classless is enabled

C. Ensure that the interfaces can ping their directly connected neighbors

D. Ensure that an interface has been configured with an IP address and is up

On your OSPF network, routers TK1 and TK2 belong to the same Ethernet network. However, they are unable to establish an adjacency over this link. While troubleshooting this problem, you issue the "show ip ospf interface Ethernet 0"command on each router. The output from these commands is displayed below:What is the underlying cause of the routers failing to become adjacent?（）

A. The OSPF area is misconfigured.

B. The priority on TK2 should be set lower.

C. The cost on TK2 should be set lower.

D. The hello and dead timers are misconfigured.

E. You need to add a backup designated router to the network.

F. The OSPF process ID numbers do not match.