违法和不良信息举报 联系客服
免费注册 登录

When configuring an interface using SMIT and Further Configu

题目
单选题
When configuring an interface using SMIT and Further Configuration with an IP address and netmask， which of the following outcomes indicates how the routing tables will be affected？（）
A

A subnet route is automatically added

B

A default route is automatically added

C

All other routes are automatically added

D

The routing table is not affected

参考答案和解析
正确答案： A
解析： 暂无解析
如果没有搜索结果或未解决您的问题，请直接 联系老师 获取答案。
相似问题和答案

第1题：

When configuring Frame Relay using point－to－point subinterfaces, which of the following must not be configured?()

A. The local DLCI on each subinterface of the Frame Relay.

B. The Frame Relay encapsulation on the physical interface.

C. An IP address on the physical interface.

D. The subinterface type as point-to-point


参考答案：C

第2题：

When configuring system state conditions with the Cisco SecurityAgent， what is the resulting action when configuring more than one system state condition？ （）

  • A、Any matching state condition will result with the state being triggered
  • B、 Once a state condition ismet， the system ceases searching further conditions and will cause the state condition to trigger
  • C、 All specified state conditions are used as part of the requirements tobe met to for the state to trigger
  • D、 Once the state conditions are met， they become persistent and can only be removed using the Reset feature

正确答案:C

第3题：

When configuring PPP over ATM interfaces, what does the profile utility accomplish?()

A.It binds an interface to a virtual router.

B.It allows for dynamic interface creation.

C.It assigns a Domain Name Server for a session.

D.It identifies the RADIUS server to use for authentication


参考答案：B

第4题：

When configuring Frame Relay using point-to-point subinterfaces, which of the following must not be configured?（）

  • A、The local DLCI on each subinterface of the Frame Relay.
  • B、The Frame Relay encapsulation on the physical interface.
  • C、An IP address on the physical interface.
  • D、The subinterface type as point-to-point

正确答案:C

第5题：

When configuring a serial interface on a router, what is the default encapsulation?（）

  • A、atm-dxi
  • B、frame-relay
  • C、hdlc
  • D、lapb
  • E、ppp

正确答案:C

第6题：

What must be set correctly when configuring a serial interface so that higher－level protocols calculate the best route?()

A. bandwidth

B. delay

C. load

D. reliability


参考答案：A

第7题：

When configuring a multipoint GRE （mGRE） tunnel interface， which one of the following is NOT a valid configuration option：（）

  • A、 tunnel source
  • B、 tunnel destination
  • C、 tunnel key
  • D、 ip address
  • E、 tunnelvrf

正确答案:B

第8题：

Which two steps are needed when configuring multiple RPs using MSDP within a single PIM domain? ()

A. Configure a non-unique address on the loopback interface for use by the PIM RP.

B. Configure MSDP with the unique address (router ID) as the local address of the peer.

C. Configure MSDP with the non-unique address (router ID) as the local address of the peer.

D. Configure a unique address on the loopback interface, used as the PIM RP.


参考答案：A, B

第9题：

You need to configure a GRE tunnel on a IPSec router. When you are using the SDM to configurea GRE tunnel over IPsec， which two parameters are required when defining the tunnel interfaceinformation？（）

  • A、The crypto ACL number
  • B、The IPSEC mode （tunnel or transport）
  • C、The GRE tunnel interface IP address
  • D、The GRE tunnel source interface or IP address， and tunnel destination IP address
  • E、The MTU size of the GRE tunnel interface

正确答案:C,D

第10题：

Cisco AutoQoS takes the interface type and bandwidth into consideration when configuring which three QoS features？（）

  • A、voice compression methodology
  • B、LLQ
  • C、CRTP
  • D、routing protocol
  • E、LFI
  • F、trust boundary

正确答案:B,C,E

更多相关问题
相关内容