在华为路由器上的串行接口上封装PPP协议,需要在接口视图下输入的命令是( ).
第1题:
配置路由器时,封装PPP协议的命令是:()
A.encap ppp
B.ppp
C.group ppp
D.int ppp
第2题:
在Cisco路由器上串行线路的默认的二层封装协议是()。
A.CHAP
B.HDLC
C.PPP
D.SLIP
第3题:
华为Quidway路由器串口上的默认封装协议是什么()。
A.HDLC
B.PPP
C.FRAME-RELAY
D.ATM
第4题:
路由器A的配置如下 Quidway#SHOW RUN Now create configuration... Current configuration ! ! interface Ethernet0 ip address 10.2.1.1 255.255.0.0 ! interface Serial0 encapsulation ppp backup interface Serial 1 ip address 2.1.1.1 255.0.0.0 ! interface Serial1 encapsulation ppp ip address 3.1.1.1 255.0.0.0 ! interface Serial2 flowcontrol normal async mode dedicated encapsulation ppp ! Exit Router rip ! End 路由器B的配置如下 Quidway#SHOW RUN Now create configuration... Current configuration ! ! interface Ethernet0 ip address 10.1.1.1 255.255.0.0 ! interface Serial0 encapsulation ppp backup interface Serial 1 ip address 2.1.1.1 255.0.0.0 ! interface Serial1 encapsulation ppp ip address 3.1.1.1 255.0.0.0 ! interface Serial2 flowcontrol normal async mode dedicated encapsulation ppp ! Exit Router rip ! End 下述说法正确的是
A、备份功能可以正常使用 B、备份功能不能正常使用 C、两端可以正常互联 D、两端不能正常互联
第5题:
路由器A的配置如下: Quidway#SHOW RUN Current configuration ! user huawei service-type ppp password 0 quidway ! interface Ethernet0 ip address 1.1.1.1 255.0.0.0 ! interface Serial0 encapsulation ppp ppp authentication chap ppp chap host huawei ip address 2.1.1.1 255.0.0.0 ! interface Serial1 encapsulation ppp ! interface Serial2 flowcontrol normal async mode dedicated encapsulation ppp ! exit ip route 0.0.0.0 0.0.0.0 2.1.1.2 preference 60 end 路由器B的配置如下 Quidway#SHOW RUN Current configuration ! user hw service-type ppp password 0 quidway ! ip address 3.1.1.1 255.0.0.0 ! interface Serial0 clock-select DTECLK1 encapsulation ppp ppp chap host huawei ip address 1.1.1.2 255.0.0.0 ! interface Serial1 encapsulation ppp ! interface Serial2 flowcontrol normal async mode dedicated encapsulation ppp ! exit ip route 0.0.0.0 0.0.0.0 2.1.1.2 preference 60 end 发现两端路由器不能PING同对端以太网端口,下述说法正确的是
A、A验证配置错误 B、B验证配置错误 C、A验证方路由配置错误 D、B被验证方路由配置错误
第6题:
在灵活DDR配置方式下,若本端需要接收呼叫,则必须在本端的物理接口上进行如下配置,以便确定是针对哪个拨号接口的入呼叫。( )
A.封装PPP
B.封装HDLC
C.配置PPP验证
D.配置EXEC验证
第7题:
哪个命令用来设置Cisco设备串行接口的默认封装()
A.Router(config)encapsulation hdlc
B.Router(config)encapsulation default hdlc
C.Router(config-if)encapsulation hdlc
D.Router(config-if)encapsulation ppp
第8题:
配置绑定在虚端口模板下的接口工作在MP方式的命令是()。
A.ppp multilink
B.dialer in-band
C.encapsulation mp
D.ppp multilink work
第9题:
路由器A的配置如下: Quidway#SHOW RUN Now create configuration... Current configuration ! ! interface Ethernet0 ip address 10.1.1.1 255.255.0.0 ip ospf enable area 0.0.0.1 ! interface Serial0 clock-select DTECLK1 encapsulation ppp ip address 2.1.1.1 255.0.0.0 ip ospf enable area 0.0.0.1 ! interface Serial1 encapsulation ppp ! interface Serial2 flowcontrol normal async mode dedicated encapsulation ppp ! exit router ospf enable ! end 路由器B配置如下 Quidway#SHOW RUN Now create configuration... Current configuration ! ! interface Ethernet0 ip address 10.2.1.1 255.255.0.0 ip ospf enable area 0.0.0.2 ! interface Serial0 encapsulation ppp ip address 2.1.1.2 255.0.0.0 ip ospf enable area 0.0.0.2 ! interface Serial1 encapsulation ppp ! interface Serial2 flowcontrol normal async mode dedicated encapsulation ppp ! exit router ospf enable ! End 如下说法正确的是
A、两端广域网可以联通,但局域网不可以连通 B、两端广域网不可以连通,但局域网可以连通 C、广域网和局域网都可以连通 D、广域网和局域网都不能连通
第10题:
在华为路由器上的串行接口上封装PPP协议,需要在接口视图下输入的命令是()。
A.link-protocol ppp
B.encapsulation ppp-----cisco设备下使用
C.enable ppp
D.address ppp