Router R1 is configured as shown below: router eigrp 100 network 10.0.0.0 eigrp stub Based on the information shown above, which two types of routes will be advertised？（）
第1题：
A. The i su 10.1.0.0/23 route is a suppressed route.
B. The i su 10.1. 0.0/23 route is a summary route.
C. The i su 10.1.0.0/23 route is an IS - IS external route.
D. The R1 IS - IS router is an ASBR.
E. The R1 IS - IS router is an ABR that belongs to multiple IS - IS areas.
F. The R1 IS - IS router is performing route aggregation and is suppressing the more specific 10.1.0.0/23 prefix.
第2题：
Refer to the exhibit. All routers have Protocol Independent Multicast (PIM) enabled interfaces. On the basis of the configuration provided on routers R1 and R2, which router will take on the func tion of rendezvous point (RP) for the multicast network? （）
A. both routers R1 and R2
B. router R1
C. router R2
D. none of the routers since they are not configured with static RP
第3题：
The following output on Router R1 lists details of a BGP route for 190.1.0.0/16. Which of the following is true based on this output?（）R1 show ip bgp 19 0.1.0.0/16BGP routing table entry for 190.1.0.0/16, version 121Paths: (1 available, best 1, table Default - IP - Routing - Table)Advertised to update - groups:11 2 3 41.1.1.1 from 2.2.2.2 (3.3.3.3)Origin IGP, metric 0, localpref 100, valid, internal, best
A. R1 has a neighbor 1.1.1.1 command configured.
B. R1 has a neighbor 2.2.2.2 command configured.
C. The show ip bgp command lists a line for 190.1.0.0/16 with both an ">" and an "i" on the left.
D. R1 is in ASN 1.
第4题：
A network administrator is troubleshooting the OSPF configuration of routers R1 and R2. The routers cannot establish an adjacency relationship on their common Ethernet link. The graphic shows the output of the show ip ospf interface e0 command for routers R1 and R2. Based on the information in the graphic, what is the cause of this problem?（）
A. The OSPF area is not configured properly.
B. The priority on R1 should be set higher.
C. The cost on R1 should be set higher.
D. The hello and dead timers are not configured properly.
E. A backup designated router needs to be added to the network.
F. The OSPF process ID numbers must match.
第5题：
A. The route to 10.2.0.0/16 was redistributed into EIGRP.
B. A default route has been redistributed into the EIGRP autonomous system.
C. R1 is configured with the ip summary - address command.
D. R1 is sourcing a n external EIGRP route from Null0.
E. The router at 10.1.1.2 is configured with the ip default - network 0.0.0.0 command.
F. R1 is configured with the variance command.
第6题：
A. Router R1 will only establish full adjacency with the DR and BDR on broadcast multi- access networks.
B. Router R2 has been elected as a DR for the broadcast multiaccess network in OSPF area 1.
C. Routers R1 and R2 are configured as stub routers for OSPF area 1 and OSPF area 2.
D. Router R1 and R2 are configured for a virtual link between OSPF area 1 and OSPF area 2.
E. The Hello parameters on routers R1 and R2 do not m atch.
第7题：
A.Router R1 is waiting for a reply from the neighbor 10.1.2.1 to the hello message sent out inquiring for a second successor to network 10.6.1.0/24
B.Router R1 can send traffic destined for network 10.6.1.0/24 out of interface FastEthernet0/0
C.Router R1 is waiting for a reply from the neighbor 10.1.2.1 to the hello message sent out before it declares the neighbor unreachable
D.Router R1 is waiting for a reply from the neighbor 10.1.2.1 in response to the query sent out about network 10 .6.1.0/24
第8题：
On Router R1, process EIGRP 1 is redistributing routes from process OSPF 2, calling route - map fred with the redistribute ospf 2 command. R1 has learned intra - area routes for 10.1.1.0/24 and10.1.2.0/24 in part due to the Type 2 LSAs known for each subnet. The route map filters route 10.1.1.0/24 and allows 10.1.2.0/24 througH.Which of the following co mmands on router R1 list subnet 10.1.1.0/24?（）
A. show ip route
B. show ip eigrp topology
C. show ip ospf topology
D. show ip eigrp topology 10.1.1.0/24
第9题：
A. The no auto - summary command has not been issued under the EIGRP process on both routers.
B. Interface E0 on router R1 has not been configured with a secondary IP address of 10.1.2.1/24.
C. EIGRP cannot exchange routing updates with a neighbor‘s router interface that is configured with tw o IP addresses.
D. EIGRP cannot form neighbor relationship and exchange routing updates with a secondary address.
第10题：
Five minutes after issuing the show running-config command, a technician enters the command again and notices that several access list statements have been altered. Because of this, the technician believes that the router is being configured by an unknown person through Telnet. Before changing the router passwords, the technician would like to discover if anyone is connected to the router by Telnet and stop them from making further changes. Which commands will accomplish these options?（）