Based on the following items， which two types of interfaces are found on all network-based IPS sensors？（）A、Loopback interfaceB、Command and control interfaceC、Monitoring interfaceD、Management interface

题目

Based on the following items， which two types of interfaces are found on all network-based IPS sensors？（）

A、Loopback interface
B、Command and control interface
C、Monitoring interface
D、Management interface

参考答案和解析

正确答案:B,C

如果没有搜索结果或未解决您的问题，请直接联系老师获取答案。

相似问题和答案

第1题：

Which two loopback types are supported for serial interfaces on Juniper devices?()

A.Local

B.Far End

C.Remote

D.Bidirectional

参考答案：A, C

第2题：

If all OSPF routers in a single area are configured with the same priority value,what value dose a router use for the ODPF router ID in the absence of a loopback interface?()

A. the IP address of the first Fast Ethernet interface

B. the IP address of the console management interface

C. the highest IP address among its active interfaces

D. the lowest IP address among its active interfaces

E. the priority value until a loopback interface is configured

参考答案：C

第3题：

You have a firewall enforcer receiving resource access policies from a Junos Pulse Access Control Service. You are using Network and Security Manager (NSM) for configuration management on that firewall. The firewall can also be configured using its built-in command-line interface (CLI) or Web-based user interface (WebUI).To avoid conflicting configurations, which two interfaces must you use to configure the firewall enforcer?（）

A. CLI

B. WebUI

C. NSM

D. Junos Pulse Access Control Service

参考答案：C, D

第4题：

Which of the following is not an essential prerequisite for AutoQoS to be correctly applied to aninterface？（Choose all that apply.）（）

A、The interface must be configured as a Multilink PPP interface
B、The correct bandwidth should be configured on the interface
C、A QoS policy must not be currently attached to the interface
D、CEF must be enabled
E、AutoQoS must be enabled globally before it can be enabled on the interface
F、An IP address must be configured on the interface if its speed is equal to or less than 768 kbps

正确答案:A,E

第5题：

Which two commands can be used to verify a trunk link configurationt status on a given cisco switch?()

A.show interfaces interface

B.show interfaces interface trunk

C.show interfaces interface switchport

D.show ip interface brief

E.show interfaces vlan

参考答案：B, C

第6题：

Which one of the following commands will display the placement and direction of an IP access control list on the interfaces of a router?()

A. show interface list

B. show ip route

C. show ip interface

D. show ip interface brief

E. show interface

参考答案：C

第7题：

Two switches are connected through a trunk link.which two commands show that there is a native VLAN mismatch on that link?()

A.show interfaces interface

B.show vlan bri

C.show interfaces interface switchport

D.show interface interface trunk

E.show interfaces vlan

参考答案：C, D

第8题：

A customer is deploying a new Junos Pulse Access Control Service and has completed the initial boot configuration as prompted using a serial connection. The customer now wants to complete the rest of the configuration using the admin GUI.Into which port on the Junos Pulse Access Control Service should the customer plug the network cable to enable access to the admin GUI?（）

A. the internal interface

B. the external interface

C. the management interface

D. the console interface

参考答案：A

第9题：

If all OSPF routers in a single area are configured with the same priority value,what value dose a router use for the ODPF router ID in the absence of a loopback interface?（）

A、the IP address of the first Fast Ethernet interface
B、the IP address of the console management interface
C、the highest IP address among its active interfaces
D、the lowest IP address among its active interfaces
E、the priority value until a loopback interface is configured

正确答案:C

第10题：

Router R1, a branch router, connects to the Internet using DSL. The engineer plans to use a configuration with a dialer interface. The answers list a feature and interface on which the feature could be configured. Which combinations accurately describe the interface under which a feature will be configured?（）

A、PPP on the ATM interface
B、VPI/VCI on the dialer interface
C、IP address on the ATM interface
D、CHAP on the dialer interface

正确答案:D

Based on the following items， which two types of interfaces are found on all network-based IPS sensors？（）A、Loopback interfaceB、Command and control interfaceC、Monitoring interfaceD、Management interface

题目

参考答案和解析

相似问题和答案

更多相关问题

相关内容