An administrator wants to have the flexibility to dynamically move a fibre channel PCI card between given LPARs. For each given LPAR how should they add the PCI card to the LPAR profile?（）A、Add the fibre channel card as hared?Add the fibre channel card as

第1题：

第2题：

A Fibre Channel fabric （or Fibre Channel switched fabric， FC-SW） is a switched fabric of FibreChannel devices enabled by a Fibre Channel switch. Fabrics are normally subdivided by Fibre Channel zoning. Each fabric has a name server and provides other services. Higher redundancy over FC-AL，P2P.Which path selection protocol is used by Fibre Channel fabrics？（）

• A、 OSPF
• B、 RIP
• C、 FSPF
• D、 VSANs

第3题：

第4题：

A customer wants to boot from SAN with their IBM BladeCenter infrastructure.  What is required for the customer to be able to perform this？ （）

• A、4GB Modular Flash Drive for each Blade Server and Dual 15.8GB 2.5 Solid State Drive for each Blade Server 
• B、Cisco Intelligent Gb Ethernet Switch Module and IBM BladeCenter Copper Pass-thru Module 
• C、Fibre Channel Expansion Card for each Blade Server and Fibre Channel SAN Switch Module 
• D、Cisco Intelligent Gb Ethernet Switch Module and Dual 15.8GB 2.5 Solid State Drive for each Blade Server

第5题：

A customer is ready to place an order for a p5-570 Express.  The external storage proposed for this solution is a 1TB FAStT600 storage server.  The customer now wishes to attach a SCSI LTO-2 tape drive to the server to enable them to backup their data.  Which of the following should the pSeries technical specialist recommend for the tape drive？（）

• A、Add a PCI-X Dual Channel Ultra320 SCSI Adapter （FC 5712）.
• B、Add a PCI-X Fibre Channel Adapter （FC 5716）.
• C、Add the optional External SCSI Port Enablement Cable （FC 4273）.
• D、Use the integrated external SCSI port on the p5-570 Express server.

第6题：

In a Cisco Unified Computing System， where are SAN port channels connected to？（）

• A、 Only to Cisco Fibre Channel switches
• B、 Only to Cisco Fibre Channel switches in NPIV mode
• C、 To any Fibre Channel switch
• D、 Directly to storage arrays
• E、 Only to Nexus Switches

第7题：

Which of the following describes the advantage of using Fibre Channel over Ethernet （FCoE） in POWER6 and POWER7 Blades？（）

• A、The FCoE card provides both LAN and fibre channel function from a single card on the blade. 
• B、The FCoE advanced technology removes the need for any BladeCenter switching to support this function.
• C、Component reliability on the fibre channel over Ethernet is higher than on regular Ethernet and fibre channel adapters.
• D、The AIX device driver for FCoE has been completely rewritten for the current adapter， eliminating errors and performance issues.

第8题：

第9题：

Company.com wants to reassign a host bus adapter （HBA） from one partition to another to  handle increased I/O workload on that partition. What needs to be done to dynamically move the card？（）

• A、Use the rmdev command to remove the card from the current partition before doing the DLPAR process.
• B、Take the source partition down and do the DLPAR function on the target partition.
• C、Assign the card to the required section of the target partition and run cfgmgr.
• D、Dynamically remove the card from the source and add to target profile then reactivate the target profile.

第10题：

An administrator needs to connect servers to the Fiber Channel SAN. Which of the following should the administrator install in the servers to allow this connection？（）

• A、Riser
• B、HBA
• C、SCSI card
• D、SAS card