ping
trace
show ip route
show interface
show cdp neighbors
第1题:
While troubleshooting an issue in the Ezonexam LAN you notice that a network interface port has collision detection and carrier sensing enabled on a shared twisted pair network. From this statement, what is known about the network interface port?
A. This is an Ethernet port operating at half duplex
B. This is an Ethernet port operating at full duplex
C. This is a port on a network interface card in a PC
D. This is 10 MB/s switch port
E. This is a 100 MB/s switch port
F. None of the above
第2题:
A technician is troubleshooting a network connectivity issue with a user‘s desktop configured touse a static IP address. The technician notes the following configuration:Which of the following changes will allow the desktop to communicate properly with remote networks?()
A. Changing the DNS to 172.16.1.100
B. Changing the WINS server to 172.174.136
C. Changing the netmask to 255.255.255.0
D. Changing the default gateway to 172.16.3.1
第3题:
While troubleshooting a connectivity problem on the network, you issue the ping command from your PC command prompt, but the output shows "request times out."
At which OSI layer is this problem associated with?
A.The data link layer
B.The application layer
C.The access layer
D.The session layer
E.The network layer
第4题:
A technician is troubleshooting a network connectivity issue on a MFD and would like to eliminate the possibility of another device on the network having the same IP address. The technician should:()
第5题:
While troubleshooting a network connectivity issue, you suspect that a router may be missing a route, or may be receiving bad routing information to a destination. What command should you issue to view the route that the router will use to reach a given destination?()
A. ping
B. trace
C. show ip route
D. show interface
E. show cdp neighbors
第6题:
A. Switching loop
B. Broadcast storm
C. IP conflict
D. Routing loop
第7题:
While troubleshooting a network outage, you discover that an employee brought a switch from home into the office to connect additional equipment to the network. In order to increase his speed, he connected this switch to both network ports in his office, resulting in a bridge loop.Which of these can you implement to prevent future occurrences of this issue?()
A.RSTP
B.root guard
C.BPDU guard
D.GLBP
第8题:
While troubleshooting a connectivity issue from a PC you obtain the following information:
Local PC IP address: 190.0.3.35/24
Default Gateway: 190.0.3.1
Remote Server: 190.0.5.250/24
You then conduct the following tests from the local PC:
Ping 127.0.0.1 - Unsuccessful
Ping 190.0.3.35 - Successful
Ping 190.0.3.1 - Unsuccessful
Ping 190.0.5.250 – Unsuccessful
What is the underlying cause of this problem?
A.TCP/IP not correctly installed
B.Local physical layer problem
C.NIC not functioning
D.Remote physical layer problem
E.None of the above
第9题:
While troubleshooting connectivity issues, you log into a remote router. From there,you wish to see the layer 1 and layer 2 status of the interface.Which of the following IOS commands would you issue to check the current IP addressing, as well as theyer 1 and layer 2 status of an interface?()
A. TK1# show version
B. TK1# show protocols
C. TK1# show interfaces
D. TK1# show controllers
E. TK1# show ip interface
F. TK1# show startup-config
第10题:
While troubleshooting a connectivity issue from a PC you obtain the following information: Local PC IP address: 10.0.0.35/24 Default Gateway: 10.0.0.1 Remote Sever: 10.5.75.250/24 You then conduct the following tests from the local PC: Ping 127.0.0.1 – Successful Ping 10.0.0.35 – Successful Ping 10.0.0.1 – Unsuccessful Ping 10.5.75.250 – Unsuccessful What is the underlying cause of this problem?()