Which three steps are used to configure IPv6 in JUNOS softwa

题目
多选题
Which three steps are used to configure IPv6 in JUNOS software?()
A

Assign 128-bit router id.

B

Enable a routing instance.

C

Assign IPv6 addresses to interfaces.

D

Add IPv6 family support to interfaces.

E

Enable IPv6-capable routing protocol.

如果没有搜索结果或未解决您的问题,请直接 联系老师 获取答案。
相似问题和答案

第1题:

You wish to configure IPv6 support on a router which does not have any current IPv4 configuration.Which three steps are used to configure IPv6 with an accompanying IGP in JUNOS software? ()

A. set protocols isis inet6

B. set routing-options router-id router-id

C. set protocols ospf3 area 0 interface all

D. set interface fe-0/0/1 unit 0 family inet6

E. set routing-options ipv6-router-id router-id


参考答案:B, C

第2题:

Which three of the following steps are mandatory when configuring MPLS on Cisco IOS? ()(Choose three.)

A. start LDP

B. enable CEF switching

C. configure the MPLS ID

D. disable IP TTL propagation

E. configure conditional label advertising

F. enable label switching on frame mode interfaces


参考答案:A, B, F

第3题:

In the Junos Pulse Access Control Service, which three actions are only available in the admin GUI? ()

A. Take a "System Snapshot"

B. Configure "Licensing"

C. Review the "Events"

D. Set the date and time

E. Upgrade or downgrade the firmware


参考答案:B, D, E

第4题:

In the Junos Pulse Access Control Service, which three actions are only available in the admin GUI? ()

  • A、Take a "System Snapshot"
  • B、Configure "Licensing"
  • C、Review the "Events"
  • D、Set the date and time
  • E、Upgrade or downgrade the firmware

正确答案:B,D,E

第5题:

Which three of these items are found within the router advertisement message of IPv6 stateless autoconfiguration?() (Choose three.)

  • A、flags indicating the kind of autoconfiguration that can be done by hosts
  • B、default router information
  • C、/64 prefix that can be used on the link and the lifetime of the prefix
  • D、IPv6 DHCP server address information

正确答案:A,B,C

第6题:

In JUNOS software, which three routing protocols can be used to route IPv6?()

A. IS-IS

B. Static

C. RIPv2

D. OSPFv2

E. MP-BGP


参考答案:A, B, E

第7题:

Which three approaches can be used while migrating from an IPV4 addressing scheme to an IPV6 scheme.()

A. statically map IPV4 address to IPV6 addresses

B. configuration IPv4 tunnels between IPV6 islands

C. use DHCPv6 to map IPV4 addresses to IPV6 addresses

D. use proxying and translation to translate IPV6 packets into IPV4 packets

E. configure IPV6 directly

F. enable dual-stack routing


参考答案:A, B, F

第8题:

You want to create a security policy on an SRX240 that redirects unauthenticated users back to the Junos Pulse Access Control Service.Which two steps must you take to accomplish this task?()

A. Configure a captive-portal service that redirects all traffic back to the Junos Pulse Access Control Service.

B. Configure a security policy that references the unified-access-control captive-portal service.

C. Configure a captive-portal service that redirects unauthenticated traffic back to the Junos Pulse Access Control Service.

D. Configure a security policy that references the unified-access-control intranet-controller service.


参考答案:B, C

第9题:

What are two steps to configure user authentication for a Junos Pulse Access Control Service?()

  • A、Configure an authentication policy as part of the user role definitions.
  • B、Configure a Sign-in Policy.
  • C、Configure authentication agents as part of the user role definitions
  • D、Configure an authentication policy as part of the authentication realm definition.

正确答案:B,D

第10题:

Which two of these steps are minimum requirements to configure OSPFv3 under IPv6?()

  • A、Configure a routing process using the command ipv6 router ospf [process-id].
  • B、Add the network statement for the interfaces on which OSPF will run.
  • C、Configure OSPF on the interface that it will run on.
  • D、Use the passive-interface command on the interfaces on which OSPF should not run.
  • E、Enable routing.

正确答案:C,E

更多相关问题