The next hop is I2's BGP RID
The next hop is I2's IP address used on the R2 - I2 neigh bor relationship
The next hop is R2's BGP RID
The next hop is R2's IP address used on the R1 - R2 neighbor relationship
第1题：
Refer to the exhibit. OSPF has been configured on all routers in the network. However, router R1 does not receive a default route to router R2 as in tended. Which configuration change would ensure that R1 would receive a default route from R2? （）
A. Add the area 1 stub command on routers R1.
B. Add the always keyword to the default - information originate configuration command on router R2.
C. Remov e the default information originate configuration command from router R2 and place it on router R1.
D. Add the ip route 5.0.0.0 255.255.255.0 0.0.0.0 command to router R2.
第2题：
Refer to the exhibit. All routers have Protocol Independent Multicast (PIM) enabled interfaces. On the basis of the configuration provided on routers R1 and R2, which router will take on the func tion of rendezvous point (RP) for the multicast network? （）
A. both routers R1 and R2
B. router R1
C. router R2
D. none of the routers since they are not configured with static RP
第3题：
Router R1, in ASN 11, learns a BGP route from BGP peer R22 in ASN 22. R1 and then uses BGP to advertise the route to R2, also in ASN 11. What ASNs would you see in the BGP table on R2 for this route?（）
A. 22
B. 11
C. 1
D. None
第4题：
计算题：两个电阻R1和R2并联连接，当R1和R2具有下列数值时，试求并联的等效电阻。①R1=R2=2Ω；②R1=2Ω，R2=0。
第5题：
A.The path of the packets will be R3 to R2 to R1.
B.The path of the packets will be R3 to R1 to R2.
C.The path of the packets will be both R3 to R2 to R1 and R3 to R1.
D.The path of the packets will be R3 to R1
第6题：
A. Router R1 will only establish full adjacency with the DR and BDR on broadcast multi- access networks.
B. Router R2 has been elected as a DR for the broadcast multiaccess network in OSPF area 1.
C. Routers R1 and R2 are configured as stub routers for OSPF area 1 and OSPF area 2.
D. Router R1 and R2 are configured for a virtual link between OSPF area 1 and OSPF area 2.
E. The Hello parameters on routers R1 and R2 do not m atch.
第7题：
Refer to the exhibit. Autonomous systems 200 and 300 have EBGP sessions established with their directly connected routers in au tonomous system 100. IGP has been configured on all routers in autonomous system 100 and they successfully exchange routing updates. Traffic originated in autonomous system 200 cannot reach the destination autonomous system 300. What configuration shoul d be done on the routers in autonomous system 100 in order for the traffic coming from autonomous system 200 to be forwarded to autonomous system 300?（）
A. IBGP session must be established between routers R1 R2 and R2 R3, and the synchronization must be turned off.
B. IBGP speakers within autonomous 100 must be fully meshed, and the synchronization must be turned on.
C. IBGP session must be established between routers R1 R2 and R2 R3, and the synchronization must be turned on.
D. IBGP session mu st be established between routers R1 and R3, and the synchronization must be turned off.
E. IBGP speakers within autonomous 100 must be fully meshed, and the synchronization must be turned off.
F. IBGP session must be established between routers R1 and R3, and the synchronization must be turned on.
第8题：
Refer to the exhibit. Routers R1 and R2 have established a neighbor relationship and are exchanging routing information. The network design requires that R1 r eceive routing updates from R2, but not advertise any routes to R2. Which configuration command sequence will successfully accomplish this task? （）
A. R1(config)# router eigrp 1 R1(config - router)# passive - interface serial 0
B. R1(config)# access - list 2 0 deny any R1(config)# router eigrp 1 R1(config - router)# distribute - list 20 out serial 0
C. R2(config)# access - list 20 permit any R2(config)# router eigrp 1 R2(config - router)# distribute - list 20 in serial 0
D. R1(config)# access - list 20 permit any R 1(config)# router eigrp 1 R1(config - router)# distribute - list 20 in serial 0
E. R2(config)# access - list 20 deny any R2(config)# router eigrp 1 R2(config - router)# distribute - list 20 out serial 0
F. R2(config)# router eigrp 1 R2(config - router)# passive - interface serial 0
第9题：
两个电阻R1和R2做串联连接，当R1和R2具有以下数值时，试求串联的等效电阻： ①R1＝R2＝1Ω；②R1＝3Ω，R2＝6Ω。
①R＝R1＋R2＝1＋1＝2（Ω）
②R＝R1＋R2＝3＋6＝9（Ω）
①的串联的等效电阻是2Ω；②的串联等效电阻为9Ω。
略
第10题：
Routers R1 and R2 are EIGRP neighbors. R1 has been configured with the eigrp stub connected command. Which of the following is true as a result？（）