违法和不良信息举报 联系客服
免费注册 登录

During startup, the router displays the following error mess

题目
单选题
During startup, the router displays the following error message: boot: cannot open "flash:" What will the router do next?（）
A

Because of damaged flash memory， the router will fail the POST

B

It will attempt to locate the IOS from a TFTP server. If this fails， it will initiate the setup dialog.

C

It will attempt to locate the IOS from a TFTP server. If this fails， it will load a limited IOS from ROM

D

It will attempt to locate the configuration file from a TFTP server. If this fails， it will initiate the setup dialog.

E

It will attempt to locate the configuration file from a TFTP server. If this fails， it will load a limited configuration from ROM

如果没有搜索结果或未解决您的问题，请直接 联系老师 获取答案。
相似问题和答案

第1题：

During startup, router VE1 displays the following error message:

boot: cannot open "flash:"

What will VE1 do next?

A. It will attempt to locate the configuration file from a TFTP server. If this fails, it will initiate the setup dialog.

B. It will attempt to locate the IOS from a TFTP server. If this fails, it will load a limited IOS from ROM.

C. It will attempt to locate the configuration file from a TFTP server. If this fails, it will load a limited configuration from ROM.

D. Because of damaged flash memory, the router will fail the POST.

E. It will attempt to locate the IOS from a TFTP server. If this fails, it will initiate the setup dialog.

F. None of the above


正确答案：B
B 解析：Explanation:
The boot sequence of a Cisco router is shown below:
Booting up the router and locating the Cisco IOS
1. POST (power on self test)
2. Bootstrap code executed
3. Check Configuration Register value (NVRAM) which can be modified using the config-register command

0 = ROM Monitor mode
1 = ROM IOS
2 - 15 = startup-config in NVRAM

4. Startup-config file: Check for boot system commands (NVRAM)
If boot system commands in startup-config
a. Run boot system commands in order they appear in startup-config to locate the IOS
b. [If boot system commands fail, use default fallback sequence to locate the IOS (Flash, TFTP, ROM)?]

If no boot system commands in startup-config use the default fallback sequence in locating the IOS:
a. Flash (sequential)
b. TFTP server (netboot)
c. ROM (partial IOS) or keep retrying TFTP depending upon router model

5. If IOS is loaded, but there is no startup-config file, the router will use the default fallback sequence for locating the IOS and then it will enter setup mode or the setup dialogue.

6. If no IOS can be loaded, the router will get the partial IOS version from ROM

第2题：

A system powers on, begins POST, displays the BIOS version information and then hangs with the error message ‘Error loading operating system’. Which of the following is MOST likely the cause of this issue? （）

A. A virus has infected the system

B. Corrupted BOOT.INI file

C. Corrupt MBR

D. Boot sector corruption


参考答案：C

第3题：

After working all night and successfully configuring a Cisco router for the Ezonexam network you save your changes on the startup config, reboot the router, and go out for a cigarette. When you return, none of your changes are active and the router boots to the initial configuration mode! Which of the choices below indicates the source of your problem?

A．Hardware failure in NVRAM prevents the router from loading the config

B．Startup-config in flash is corrupt and cannot be analyzed

C．Router configuration-register set to bypass startup configuration

D．Startup-config in NVRAM is corrupt and cannot be analyzed

E．None of the above


正确答案：C
解析：Explanation:
The default configuration-register setting of 0x2102 loads the IOS from flash and the configuration from NVRAM.
However, for password recovery, you can set the register to 0x2142 and the startup-config file in NVRAM will be bypassed. The problem described here is that the config register was not changed back to 0x2102 before the router was rebooted, so the active configuration is bypassed. Simply setting the config register back to 0x2102 will fix this problem.

Incorrect Answers:
A, B, D. All of these describe hardware or software errors. In the event that this is the problem, errors will be generated and the router will fail to boot properly. In these cases, the router will not return to the initial startup configuration.

第4题：

During startup, the router displays the following error message: boot: cannot open "flash:" What will the router do next（）。

  • A、Because of damaged flash memory, the router will fail the POST.
  • B、It will attempt to locate the IOS from a TFTP server. If this fails, it will initiate the setup dialog.
  • C、It will attempt to locate the IOS from a TFTP server. If this fails, it will load a limited IOS from ROM.
  • D、It will attempt to locate the configuration file from a TFTP server. If this fails, it will initiate the setup dialog.
  • E、It will attempt to locate the configuration file from a TFTP server. If this fails, it will load a limited configuration from ROM.

正确答案:C

第5题：

During startup, the router displays the following error message: boot: cannot open "flash:" What will the router do next?（）

  • A、Because of damaged flash memory， the router will fail the POST
  • B、It will attempt to locate the IOS from a TFTP server. If this fails， it will initiate the setup dialog.
  • C、It will attempt to locate the IOS from a TFTP server. If this fails， it will load a limited IOS from ROM
  • D、It will attempt to locate the configuration file from a TFTP server. If this fails， it will initiate the setup dialog.
  • E、It will attempt to locate the configuration file from a TFTP server. If this fails， it will load a limited configuration from ROM

正确答案:C

第6题：

Given the following router output,which configuration file will the router use at its next reload?()

A.config

B.clientqos.cnf

C.startup-config

D.running-configuration


参考答案：D

第7题：

A network administrator enters the following command on a router: logging trap 3. What are three message types that will be sent to the Syslog server? ()

A.informational

B.emergency

C.warning

D.critical

E.debug

F.error


参考答案：B, D, F

第8题：

View the Exhibit to examine the error during the database startup.You open an RMAN session for the database instance. To repair the failure, you executed the following as the first command in the RMAN session:RMAN> REPAIR FAILURE;Which statement describes the consequence of the command?（）

A. The command performs the recovery and closes the failures.

B. The command only displays the advice and the RMAN script required for repair.

C. The command produces an error because the ADVISE FAILURE command has not been executed before the REPAIR FAILURE command.

D. The command executes the RMAN script to repair the failure and removes the entry from the Automatic Diagnostic Repository (ADR).


参考答案：C

第9题：

A network administrator enters the following command on a router: logging trap 3. What are three message types that will be sent to the Syslog server? （）

  • A、informational
  • B、emergency
  • C、warning
  • D、critical 
  • E、debug
  • F、error

正确答案:B,D,F

第10题：

Which of the following statements about authentication responses and conditions is true? （）(Choosetwo.)

  • A、When a router receives a failure response, it stops querying authentication methods.
  • B、When a router receives an error response, it stops querying authentication methods.
  • C、If the router receives a failure response from an authentication method, it queries the next method.
  • D、The router does not differentiate between failure and error responses; the authentication process is always interrupted.
  • E、If it receives no response from the authentication method, a router will determine the error condition On its own; the router also has the option to proceed to the next method in a list if configured accordingly.

正确答案:A,E

更多相关问题
相关内容