Router1 has specific boot system command that instruct it to load IOS from TFTP server.
Router1 is acting as a TFTP server for other routers.
Router1 cannot locate a valid IOS image in flash memory.
Router1 defaulted to ROMMON mode and loaded the IOS image from a TFTP server.
Cisco routers will first attempt to load a image from TFTP for management purposes.
第1题：
Refer to the exhibit. Two routers are connected by Frame Relay and are running OSPF bet ween them. Each router has been configured with the appropriate network statements under router ospf 1, but the routers are not forming an adjacency. Which of the following three commands could be configured on each router to correct this problem?（）
A. RouterC(config - if)#ip ospf network broadcast RouterD(config - if)#ip ospf network broadcast
B. RouterC(config - if)#ip ospf network point - to - point RouterD(config - if)#ip ospf network point - to - point
C. RouterC(config - router)#neighbor 10.100. 100.4 RouterD(config - router)#neighbor 10.100.100.3
D. RouterC(config - router)#neighbor 10.255.255.254 RouterD(config - router)#neighbor 10.255.255.253
第2题：
Refer to the exhibit. You have completed an OSPF implementation, and you are verifying OSPF operation. You notice that router A and router B are stuck in the two - way state. From the show ip ospf interface command output, what is the cause of this issue?（）
A. All OSPF implementations must have at le ast one interface in area 0.
B. You are attempting to run in the broadcast mode over an NBMA interface.
C. Both routers are configured to function as a BDR; therefore, there is no DR router.
D. Someone has changed the OSPF router ID; therefore you must clear the OSPF process.
E. The OSPF priority is set to 0 on both routers; therefore neither can become the DR.
第3题：
Refer to the exhibit. OSPF is configured on all routers in the network. Area 5 is configured as an NSSA areA. The RIPv2 routes are redistributed into the OSPF domain on router R5. What two types of LSAs will be originated by router R5?（）
A. type 1 Router LSA
B. type 2 Network LSA
C. type 3 Network Summary LSA
D. type 4 ASBR Summary LSA
E. type 5 AS External LSA
F. type 7 NSSA External LSA
第4题：
A.The router is in area 49.0001.0002
B.The router acts as a Level 1 - 2 router
C.CLNS routing is enable d for the router
D.The router has a system ID of 0003.0004
E.The interfaces have a functional IS - IS configuration
F.The network service access point selector (NSEL) byte has a value of 0
第5题：
A. the serial 1/1 address
B. the serial 2/0 address
C. a randomly generated internal address
D. the configured router - id address
第6题：
Refer to the exhibit. A network administrator wants to reduce the number of OSPF routes advertised from Area 1 into Area 2. As the router configuration specialist, what two things would you do to accomplish this goal?（）
A. Enter the configuration on router B1.
B. Enter the configuration on router B4.
C. On the same router, enter the Summary - address 10.10.1.0 255.255.255.128 subcommand.
D. On the same router, enter the Area 1 range 10.10.1.0 255.255.255.128 subcommand.
E. On the same ro uter, enter the Area 2 range 10.10.1.0 255.255.255.128 subcommand.
第7题：
A.The NProuter has two OSPF neighbors in the "Full" adjacency state
B.The NProuter serial0/0 interface has the OSPF dead timer set to 10 seconds
C.The NProuter serial0/0 interface has been configured with an OSPF network type of "pointtopoint"
D.The 10.1.1.1 and 10.1.1.2 routers are not using the default OSPF dead and hello timers setting
E.The "Mismatched" error is caus ed by the expiration of the OSPF timers
第8题：
Refer to the exhibit. EIGRP has been configured on router D. Router C is performing mutual redistribution between EI GRP and OSPF. While verifying that the redistribution is functioning properly, you discover that while router C has all of the EIGRP routes in its routing table, router A does not have any routes from the EIGRP domain. What on router C may be the cause o f the problem?（）
A. The no auto - summary command needs to be added under router eigrp 1
B. The subnets keyword was not included in the redistribute command under router ospf 1
C. The metric specified for the redistributed EIGRP routes is too large; m aking the EIGRP routes unreachable by router A
D. The default - information originate command needs to be added under router ospf 1
E. The administrative distance of either OSPF or EIGRP must be changed so that EIGRP has a higher administrative distanc e than OSPF
第9题：
A. The default administrative distance has been changed.
B. IS - IS is not enabled.
C. Three physical interfaces are taking part in integrated IS - IS.
D. IS - IS is not redistributing any oth er routing protocols.
E. There are two neighboring routers sending IS - IS routing information.
F. Address summarization is configured.
第10题：
A. This is the designated router (DR) on the FastEthernet 0/0 link.
B. The output was generated by the show ip interface c ommand.
C. The router was configured with the commands:r outer ospf 1 network 172.16.6.0 0.0.0.255 area 1
D. The IP address of the backup designated router (BDR) is FE80::205:5FFF:FED3:5808.
E. Interface FastEthernet 0/0 was configured with the ipv6 o spf 1 area 1 command.
F. OSPF version 2 has been enabled to support IPv6.