On the assumption that every OSPF router in a particular are

You have completed an OSPF implementation, and you are verifying OSPF operation. During this verification, you notice that the OSPF route of 172.16.10.0 is repeatedly appearing and disappearing from the routing table. Further investigation finds that the OSPF CPU utilization is very high and the routers are constantly performing SPF calculations. You determine that 172.16.20.2 is the source of the 172.16.10.0 route. Using the show ip ospf database router 172.16.20.1 command, you notice that when this show command is performed repeatedly, the contents of the LSA change every few seconds.What could be the cause of this problem?（）

A. OSPF authentication errors between some of the routers

B. Two routers have the same OSPF router ID

C. Issues with mistuned OSPF timers

D. OSPF LSA pacing issues between some of the routers

E. OSPF neighbor adjacency problems between some of the routers

Open Shortes t Path First (OSPF) is a routing protocol developed for Internet Protocol (IP) networks by the Interior Gateway Protocol (IGP) working group of the Internet Engineering Task Force (IETF).Which two statements best describe the OSPF link - state routing pro tocol?（）

A. OSPF sends updates every 10 seconds

B. OSPF sends triggered updates when a network change occurs

C. When a link state is changed, the router that detected the change creates a link - state advertisement (LSA) and propagates it to all OSPF devices using the 224.0.0.6 multicast address

D. OSPF sends summaries of individual link- state entries every 30 minutes to ensure LSDB synchronization

某园区网采用OSPF路由协议，参与OSPF的网络地址是169.111.0.0/16 Cisco路由器的正确配置是

A．Router (config) #router ospf 63 Router (config-router) #network 169.111.0.0 0.0.0.0 area 0 Router (config-router) #area 0 range 169.111.0.0 255.255.0.0

B．Router (config) #router ospf 63 Router (config-router) # network 169.111.0.0 255.255.0.0 area 0 Router (config-router) #area 0 range 169.111.0.0 255.255.0.0

C．Router (config) #router ospf 63 Router (config-router) #network 169.111.0.0 0.0.255.255 area 0 Router (config-router) #area 0 range 169.111.0.0 255.255.0.0

D．Router (config) #router ospf 63 Router (config-router) #network 169.111.0.0 0.0.255.255 area 0 Router (config-router) #area 0 range 169.111.0.0 0.0.255.255

A.Router(config)#router ospf 1

B.Router(config)#router ospf 0

C.Router(config)#router ospf area 0

D.Router(config-router)#network 192.168.16.0 0.0.0.255 area 0

E.Router(config-router)#network 192.168.16.0 0.0.0.255 0

F.Router(config-router)#network 192.168.16.0 255.255.255.0 area 0

A. router ospf ipv6 process - id

B. ipv6 ospf process - id

C. router ospf process - id

D. ipv6 router ospf process - id

A. The IP address of the first Fast Ethernet interface.

B. The IP address of the console management interface.

C. The highest IP address among its active interfaces.

D. The lowest IP address among its active interfaces.

E. There will be no router ID until a loopback interface is configured.

Refer to the exhibit. Two routers are connected by Frame Relay and are running OSPF bet ween them. Each router has been configured with the appropriate network statements under router ospf 1, but the routers are not forming an adjacency. Which of the following three commands could be configured on each router to correct this problem?（）

A. RouterC(config - if)#ip ospf network broadcast RouterD(config - if)#ip ospf network broadcast

B. RouterC(config - if)#ip ospf network point - to - point RouterD(config - if)#ip ospf network point - to - point

C. RouterC(config - router)#neighbor 10.100. 100.4 RouterD(config - router)#neighbor 10.100.100.3

D. RouterC(config - router)#neighbor 10.255.255.254 RouterD(config - router)#neighbor 10.255.255.253