违法和不良信息举报 联系客服
免费注册 登录

多选题In a PIM topology using anycast RP, in which two ways can the RPs share group information? （）AConfigure MSDP between RPs.BRedistribute multicast information in your IGP.CAdvertise S, G entries using MBGP.DConfigure PIM to advertise group information be

题目
多选题
In a PIM topology using anycast RP, in which two ways can the RPs share group information? （）
A

Configure MSDP between RPs.

B

Redistribute multicast information in your IGP.

C

Advertise S, G entries using MBGP.

D

Configure PIM to advertise group information between RPs.

如果没有搜索结果或未解决您的问题，请直接 联系老师 获取答案。
相似问题和答案

第1题：

Which command can be used to check the assignment of RPs to multicast groups？（）

  • A、show ip pim rendez-vous
  • B、show ip rpf rp mapping
  • C、show ip pim rp mapping
  • D、show ip pim rp info
  • E、show ip pim

正确答案:C

第2题：

In PIM-SM what control plane signaling must a multicast source perform before it begins to send multicasttraffic to a group？（）

  • A、The source must send a PIM Register message to the rendezvous point （RP）.
  • B、The source must first join the multicast group using IGMP before sending.
  • C、The source must perform a Request to Send （RTS） and Clear to Send （CTS） handshake with the  PIM designated router （DR）.
  • D、No control plane signaling needs to be performed； the source can simply begin sending on the local  subnet.

正确答案:D

第3题：

Which two steps are needed when configuring multiple RPs using MSDP within a single PIM domain? ()

A. Configure a non-unique address on the loopback interface for use by the PIM RP.

B. Configure MSDP with the unique address (router ID) as the local address of the peer.

C. Configure MSDP with the non-unique address (router ID) as the local address of the peer.

D. Configure a unique address on the loopback interface, used as the PIM RP.


参考答案：A, B

第4题：

In a PIM topology using anycast RP, in which two ways can the RPs share group information? （）

  • A、Configure MSDP between RPs.
  • B、Redistribute multicast information in your IGP.
  • C、Advertise S, G entries using MBGP.
  • D、Configure PIM to advertise group information between RPs.

正确答案:A,D

第5题：

Which two steps are needed when configuring multiple RPs using MSDP within a single PIM domain? （）

  • A、Configure a non-unique address on the loopback interface for use by the PIM RP.
  • B、Configure MSDP with the unique address (router ID) as the local address of the peer.
  • C、Configure MSDP with the non-unique address (router ID) as the local address of the peer.
  • D、Configure a unique address on the loopback interface, used as the PIM RP.

正确答案:A,B

第6题：

When building an IP multicast domain using PIM which mode assumes  that other routers do not want to forward multicast packets for the group?（）

  • A、PIM - DM
  • B、PIM - SM
  • C、PIM - RP
  • D、CGMP
  • E、IGMP snooping

正确答案:B

第7题：

In what PIM topology would you use MSDP within a single domain？（）

  • A、Auto-RP
  • B、Anycast RP
  • C、Bootstrap router
  • D、PIM sparse mode

正确答案:B

第8题：

When building an IP multicast domain using PIM which mode assumes that other routers do not want to forward multicast packets for the group?()

A. PIM - DM

B. PIM - SM

C. PIM - RP

D. CGMP

E. IGMP snooping


参考答案：B

第9题：

Which are correct descriptions and configurations of Anycast RP？（）

  • A、In Anycast RP， two or more RPs are configured with the same IP address on loopback interfaces.
  • B、Anycast RP provides redundancy and load-sharing capabilities.
  • C、Routers with Anycast RP can be configured statically （loopback 1.1.1.1）with the command ip pim rp-address 1.1.1.1
  • D、Routers with Anycast RP can be configured statically （loopback 1.1.1.1）with the command ip rp-address pim 1.1.1.1
  • E、Routers with Anycast RP can be configured statically （loopback 1.1.1.1）with the command ip anycast-rp pim 1.1.1.1

正确答案:A,B,C

第10题：

In PIM-SM what control plane signaling must a multicast source perform before it begins to send multicast traffic to a group？（）

  • A、The source must send a PIM Register message to the rendezvous point （RP）
  • B、The source must first join the multicast group using IGMP before sending
  • C、The source must perform a Request to Send （RTS） and Clear to Send （CTS） handshake with the PIM designated router （DR）
  • D、No control plane signaling needs to be performed；the source can simply begin sending on the local subnet

正确答案:D

更多相关问题
相关内容