Refer to the exhibit. Why has this switch not been elected the root bridge for VLAN1?()

题目
Refer to the exhibit. Why has this switch not been elected the root bridge for VLAN1?()

A.It has more than one interface that is connected to the root network segment.

B.It is running RSTP while the elected root bridge is running 802.1d spanning tree.

C.It has a higher MAC address than the elected root bridge.

D.It has a higher bridge ID than the elected root bridge.

如果没有搜索结果或未解决您的问题,请直接 联系老师 获取答案。
相似问题和答案

第1题:

Refer to the exhibit. Which statement is true?()

A.The Fa0/11 role confirms that SwitchA is the root bridge for VLAN 20.

B.VLAN 20 is running the Per VLAN Spanning Tree Protocol.

C.The MAC address of the root bridge is 0017.596d.1580.

D.SwitchA is not the root bridge, because not all of the interface roles are designated.


参考答案:D

第2题:

Refer to the exhibit. Based on the information given. Which switch will be elected root bridge and why?()

A.Switch A ,because it has the lowest MAC address

B.Switch C,because it has the lowest priority

C.Switch B,because it has the highest MAC address

D.Switch C,because it is the most centrally located switch

E.Switch A,because it is the most centrally located switch

F.Switch D,because it has the highest priority


参考答案:B

第3题:

Refer to the exhibit. Switch port FastEthernet 0/24 on AlSwitch1 will be used to create an IEEE 802.1Q- complaint trunk to another switch. Based on the output shown, What is the reason the trunk does not form, even thought the proper cabling has been attached?()

A.VLANs have not been created yet

B.An IP address must be configured for the port

C.The port is currently configured for access mode

D.The correct encapsulation type has not been configured

E.The no shutdown command has not been entered for the port


参考答案:C

第4题:

Refer to the exhibit. The output that is shown is generated at a switch. Which three of these statements are true? ()

  • A、All ports will be in a state of discarding, learning, or forwarding.
  • B、Thirty VLANs have been configured on this switch.
  • C、The bridge priority is lower than the default value for spanning tree.
  • D、All interfaces that are shown are on shared media.
  • E、All designated ports are in a forwarding state.
  • F、The switch must be the root bridge for all VLANs on this switch.

正确答案:A,C,E

第5题:

The network administrator has enabled BPDU guard on the LAN.  Why is an effective way to prevent an unauthorized rogue switch from altering the spanning-tree topology of this network? ()

  • A、BPDU guard can be used to prevent invalid BPDUs from propagating throughout the network. 
  • B、BPDU guard can guarantee proper selection of the root bridge.
  • C、BPDU guard can be utilized to prevent the switch from transmitteing BPDUs and incorrectly altering the root bridge election.
  • D、BPDU guard can be utilized along with PortFast to shut down ports when a switch is connected to the port.
  • E、None of the other alternatives apply

正确答案:D

第6题:

Refer to the exhibit. Given the output shown from this Cisco Catalyst 2950, what is the most likely reason that interface FastEthernet 0/10 is not the root port for VLAN 2?()

A.This switch has more than one interface connected to the root network segment in VLAN 2.

B.This switch is running RSTP while the elected designated switch is running 802.1d Spanning Tree.

C.This switch interface has a higher path cost to the root bridge than another in the topology.

D.This switch has a lower bridge ID for VLAN 2 than the elected designated switch.


参考答案:C

第7题:

Refer to the exibit. Three cisco 2950 switches are set to their default priority sttings.During the spanningtree process,which switch will be elected as the root bridge?()

A.Switch3

B.Switch4

C.Switch2

D.Switch1


参考答案:D

第8题:

Refer to the exhibit. Which of these statements correctly describes the state of the switch once the boot process has been completed?()

A.As FastEthernet0/12 will be the last to come up, it will not be blocked by STP.

B.Remote access management of this switch will not be possible without configuration change.

C.More VLANs will need to be created for this switch.

D.The switch will need a different IOS code in order to support VLANs and STP.


参考答案:B

第9题:

Refer to Topic TestKing.com in iPAD document.Which switch is the root bridge for VLAN 1?()

  • A、TestKingD
  • B、TestKing1
  • C、TestKing2
  • D、TestKing3

正确答案:A

第10题:

Refer to the exibit. Three cisco 2950 switches are set to their default priority sttings.During the spanningtree process,which switch will be elected as the root bridge?()

  • A、Switch3
  • B、Switch4
  • C、Switch2
  • D、Switch1

正确答案:D

更多相关问题