违法和不良信息举报 联系客服
免费注册 登录

多选题What are two commands that can be used to configure MBGP for multicast?（）AUnder the BGP group, configure family inet any.BUse the set protocol MBGP command to enable MBGP.CUnder the BGP group, configure family inet multicast.DUse the set rib-group comm

题目
多选题
What are two commands that can be used to configure MBGP for multicast?（）
A

Under the BGP group, configure family inet any.

B

Use the set protocol MBGP command to enable MBGP.

C

Under the BGP group, configure family inet multicast.

D

Use the set rib-group command to copy the multicast routes into inet.1.

如果没有搜索结果或未解决您的问题，请直接 联系老师 获取答案。
相似问题和答案

第1题：

Which set of configuration commands configures MBGP on the ERX Edge Router?()

A. router bgp 100 neighbor 192.168.10.1 remote-as 200 address-family ipv4 multicast neighbor 192.168.10.1 next-hop-self

B. router bgp 100 neighbor 192.168.10.1 remote-as 200 address-family vpnv4 multicast neighbor 192.168.10.1 activate

C. router bgp 100 neighbor 192.168.10.1 remote-as 200 address-family ipv4 unicast neighbor 192.168.10.1 active

D. router bgp 100 neighbor 192.168.10.1 remote-as 200 address-family ipv4 multicast neighbor 192.168.10.1 activate


参考答案：D

第2题：

Which statement would prevent the sending of redundant route advertisements when your routereflector cluster is fully meshed?()

A. set protocols bgp group mygroup path-selection cisco-non-deterministic;

B. set protocols bgp group i-bgp no-aggregator-id;

C. set protocols bgp group mygroup no-client-reflect;

D. set protocols bgp group i-bgp damping;


参考答案：C

第3题：

You wish to configure IPv6 support on a router which does not have any current IPv4 configuration.Which three steps are used to configure IPv6 with an accompanying IGP in JUNOS software? ()

A. set protocols isis inet6

B. set routing-options router-id router-id

C. set protocols ospf3 area 0 interface all

D. set interface fe-0/0/1 unit 0 family inet6

E. set routing-options ipv6-router-id router-id


参考答案：B, C

第4题：

You wish to configure IPv6 support on a router which does not have any current IPv4 configuration.Which three steps are used to configure IPv6 with an accompanying IGP in JUNOS software? （）

  • A、set protocols isis inet6
  • B、set routing-options router-id router-id
  • C、set protocols ospf3 area 0 interface all
  • D、set interface fe-0/0/1 unit 0 family inet6
  • E、set routing-options ipv6-router-id router-id

正确答案:B,C

第5题：

Which two are correct when configuring an IP address for a Fast Ethernet interface?()

A.set interfaces fe-0/0/0 address 10.1.1.1/24

B.set interfaces fe-0/0/0.0 family inet address 10.1.1.1/24

C.set interfaces fe-0/0/0.0 address 10.1.1.1/24

D.set interfaces fe-0/0/0 unit 0 family inet address 10.1.1.1/24


参考答案：B, D

第6题：

Which two functions can be configured on the ERX Edge Router to support MBGP? ()(Choose two.)

A. address-family ipv4 unicast

B. address-family vpnv4 unicast

C. address-family ipv4 multicast

D. address-family vpnv4 multicast


参考答案：B, C

第7题：

What are two commands that can be used to configure MBGP for multicast?()

A. Under the BGP group, configure family inet any.

B. Use the set protocol MBGP command to enable MBGP.

C. Under the BGP group, configure family inet multicast.

D. Use the set rib-group command to copy the multicast routes into inet.1.


参考答案：A, C

第8题：

For maintaining separate unicast and multicast forwarding topologies, where should MBGP multicast routes be placed?()

A. inet.0

B. inet.1

C. inet.2

D. inet.4


参考答案：C

第9题：

What are the basic configuration steps to enable IS － IS?()

A. Configure the net system - id command under routerisis and enable IS - IS on each interface with the ip router isis command.

B. Configure the net sy stem - id and the network net - id commands under routerisis.

C. Configure the network net - id command(s) under routerisis and enable IS - IS on each interface with the ip router isis command.

D. Configure the network net - id command(s) and the is - type level -1- 2 command under routerisis.

E. Configure the net system - id and the network net - id commands under routerisis and enable ISIS on each interface with the ip router isis command.


参考答案：A

第10题：

Which two functions can be configured on the ERX Edge Router to support MBGP? （）(Choose two.)

  • A、address-family ipv4 unicast
  • B、address-family vpnv4 unicast
  • C、address-family ipv4 multicast
  • D、address-family vpnv4 multicast

正确答案:B,C

更多相关问题
相关内容