The Frame Relay network in the diagram is not functioning properly. What is the cause of the problem?（）
第1题：
Refer to the exhibits. Router B should advertise the network co nnected to the E0/0/0 interface to router A and block all other network advertisements. The IP routing table on router A indicates that it is not receiving this prefix from router B. What is the probable cause of the problem?（）
A. An access list on router B is causing the 192.168.3.16/28 network to be denied
B. An access list on router B is causing the 192.168.3.32/28 network to be denied
C. The distribute list on router B is referencing a numbered access list that does not exist on router B
D. The d istribute list on router B is referencing the wrong interface
第2题：
In order to troubleshoot an issue with the Testking frame relay network, you log into a remote router via a telnet session and issue the command "debug frame-relay lmi". After a long wait, you fail to see any output. What could be the cause of this problem?（）
A. The IP addresses are configured incorrectly.
B. Frame Relay LMI messages not displayed in real time.
C. The administrator must issue the enable frame-relay lmi debug command.
D. The administrator must issue the terminal monitor command.
E. Debug messages can only be received once through the console port.
F. The administrator must issue the show frame-relay lmi vty 0 4 command
第3题：
In a Bridged 1483 network, an ISP has received complaints from their subscribers of denial of service attacks.The ISP suspects these attacks are coming from other subscribers that share the same IP unnumbered interface on the ERX.What can be done to solve this problem?（）
A. Enable Proxy ARP.
B. Disable Proxy ARP.
C. Enable Inverse ARP.
D. Disable Inverse ARP.
第4题：
A. The Gallant router has the wrong LMI type configured
B. Inverse ARP is providing the wrong PVC information to the Gallant router
C. The S3 interface of the Steele router has been configured with the frame-relay encapsulation ietf command
D. The frame-relay map statement in the Attalla router for the PVC to Steele is not correct
E. The IP address on the serial interface of the Attalla router is configured incorrectly
第5题：
The Testking Central and Remote offices are configured as shown below:The remote router can be successfully pinged from the central office but the remote users can‘t access the server at the central office.Based on the output above, what do you suspect is the cause of this problem?（）
A. The Frame Relay PVC is down.
B. The IP addressing on the Central/Remote serial link is incorrect.
C. RIP routing information is not being forwarded.
D. Frame Relay inverse-ARP is not properly configured.
第6题：
A. frame-relay arp
B. frame-relay map
C. frame-relay interface-dlci
D. frame-relay lmi-type
第7题：
You are trying to bring up a new Testking location onto your existing frame relay network. The new location is using an Adtran router and you are having difficulties getting the site to connect via frame to your Cisco HQ router. What is the most likely cause of the problem?（）
A. Mismatched LMI types.
B. Incompatible encapsulation types.
C. Mismatching IP addresses.
D. Incorrect DLCI.
E. None of the above
第8题：
Refer to the exhibit. Two routers are connected by Frame Relay and are running OSPF bet ween them. Each router has been configured with the appropriate network statements under router ospf 1, but the routers are not forming an adjacency. Which of the following three commands could be configured on each router to correct this problem?（）
A. RouterC(config - if)#ip ospf network broadcast RouterD(config - if)#ip ospf network broadcast
B. RouterC(config - if)#ip ospf network point - to - point RouterD(config - if)#ip ospf network point - to - point
C. RouterC(config - router)#neighbor 10.100. 100.4 RouterD(config - router)#neighbor 10.100.100.3
D. RouterC(config - router)#neighbor 10.255.255.254 RouterD(config - router)#neighbor 10.255.255.253
第9题：
A. frame-relay arp
B. frame-relay map
C. frame-relay interface-dlci
D. frame-relay lmi-type
E. frame-relay pvc
第10题：
A.The Gallant router has the wrong LMI type configured
B.Inverse ARP is providing the wrong PVC information to the Gallant router
C.The S3 interface of the Steele router has been configured with the frame-relay encapsulation ietf command
D.The frame-relay map statement in the Attalla router for the PVC to Steele is not correct
E.The IP address on the serial interface of the Attalla router is configured incorrectly