Which interface does the Infranet Controller use to push the configuration? ()A、trusted portB、internal portC、trust interfaceD、untrust interface

题目

Which interface does the Infranet Controller use to push the configuration? ()

  • A、trusted port
  • B、internal port
  • C、trust interface
  • D、untrust interface
如果没有搜索结果或未解决您的问题,请直接 联系老师 获取答案。
相似问题和答案

第1题:

Which CLI command displays the IS-IS level used by each interface?()

A. show clns neighbor

B. show isis neighbor

C. show clns interface

D. show isis interface


参考答案:C

第2题:

When the Infranet Enforcer is set up in transparent mode, which additional resource policy must be configured to use OAC for IPsec enforcement? ()

A. IPsec Routing

B. Access Control

C. IP Address Pool

D. Source Interface


参考答案:D

第3题:

A customer is deploying a new Junos Pulse Access Control Service and has completed the initial boot configuration as prompted using a serial connection. The customer now wants to complete the rest of the configuration using the admin GUI.Into which port on the Junos Pulse Access Control Service should the customer plug the network cable to enable access to the admin GUI?()

A. the internal interface

B. the external interface

C. the management interface

D. the console interface


参考答案:A

第4题:

Which one of the following commands will display the placement and direction of an IP access control list on the interfaces of a router?()

A. show interface list

B. show ip route

C. show ip interface

D. show ip interface brief

E. show interface


参考答案:C

第5题:

To troubleshoot interface problems, you can use both the disable command and the deactivate command. Which two statements are correct?()

A.If the interface is disabled, the logical unit will administratively shutdown.

B.If the interface is deactivated, the physical interface will administratively shutdown.

C.If the interface is deactivated, the interface configuration is ignored during commit.

D.If the interface is disabled, the logical unit configuration is ignored during commit.


参考答案:B, C

第6题:

You would like to configure a fractional T1 interface on a channelized T3 controller with the following properties:Which set of configuration commands accomplishes this goal?()

A.A

B.B

C.C

D.D


参考答案:D

第7题:

Which interface does the Infranet Controller use to push the configuration? ()

A. trusted port

B. internal port

C. trust interface

D. untrust interface


参考答案:B

第8题:

Click the Exhibit button.Based on the exhibit, client PC 192.168.10.10 cannot ping 1.1.1.2.Which is a potential cause for this problem?()

A. The untrust zone does not have a management policy configured.

B. The trust zone does not have ping enabled as host-inbound-traffic service.

C. The security policy from the trust zone to the untrust zone does not permit ping.

D. No security policy exists for the ICMP reply packet from the untrust zone to the trust zone.


参考答案:C

第9题:

Router R1, a branch router, connects to the Internet using DSL. The engineer plans to use a configuration with a dialer interface. The answers list a feature and interface on which the feature could be configured.Which combinations accurately describe the interface under which a feature will be configured?()

A. PPP on the ATM interface

B. VPI/VCI on the dialer interface

C. IP address on the ATM interface

D. CHAP on the dialer interface


参考答案:D

第10题:

A network interface port has collision detection and carrier sensing enabled on a shared twisted pair network. From this statement, what is known about the network interface port()。

  • A、This is a 10 Mb/s switch port
  • B、This is a 100 Mb/s switch port
  • C、This is an Ethernet port operating at half duplex
  • D、This is an Ethernet port operating at full duplex
  • E、This is a port on a network interface card in a PC

正确答案:C

更多相关问题