违法和不良信息举报 联系客服
免费注册 登录

Refer to the exhibit. When running EIGRP, What is required f

题目
单选题
Refer to the exhibit. When running EIGRP, What is required for RouterA to exchange routing updates with RouterC?（）
A

As numbers must be changed to match on all the routers.

B

Loopback interface must be configured so a DR is elected.

C

The no auto-summary command is needed on Router A and Router C.

D

Router B needs to have two network statements, one for each connected network.

如果没有搜索结果或未解决您的问题，请直接 联系老师 获取答案。
相似问题和答案

第1题：

Refer to the exhibit. BigBids Incorporated is a worldwide auction provider. The network uses EIGRP as its routing protocol throughout the corporation. The network administrator does not understand the convergence of EIGRP. Using the output of the show ip eigrp topology all - links command, answer the administrator‘s questions.Which three networks is the router at 172.17.10.2 directly connected to?（）

A. 172.17.0.0/30

B. 172.17.1.0/24

C. 172.17.2.0/24

D. 172.17.3 .0/25

E. 172.17.3.128/25

F. 172.17.10.0/24


参考答案：C, E, F

第2题：

Refer to the exhibit. In a redundant hub - and - spoke deployment using EIGRP, what feature can be used to ensure that routers C through F are not used as transit routers for data traveling from router B to network 10.1.1.0? Select the best response.（）

A. Use address summarization at routers C, D, E, and F

B. Use the EIGRP Stub featu re on routers C, D, E, and F

C. Use passive - interface on the spoke links in routers A and B

D. Change the administrative distance in routers A and B for routes learned from routers C, D, E,and F


参考答案：B

第3题：

Refer to the exhibit. The routing protocols EIGRP and OSPF have been configured as indicated in the exhibit. Given the partial configuration of router R2, which network will be present in th e routing table of R4?（）

A. Network B

B. Network A and Network B

C. Network A

D. neither Network A nor Network B


参考答案：A

第4题：

Refer to the above exhibit. Why are the EIGRP neighbors for this router not learning the routes redistributed from OSPF?()

A. Redistribution must be enabled mutually (in both directions) to work correctly.

B. auto - summary causes the OSPF routes redistributed into EIGRP to be summarized; thus the OSPF network 116.16.34 is summarized to 116.3 4.0.0, which is already covered by the EIGRP protocol.

C. Default metrics are not configured under EIGRP.

D. Both routing protocols must have unique autonomous system numbers for redistribution to function correctly.


参考答案：C

第5题：

Refer to the exhibit. You want to use all the routes in the EIGRP topology for IP load balancing. Which two EIGRP subcommands wou ld you use to accomplish this goal?()

A. traffic - share balanced

B. distance

C. maximum- paths

D. default - network

E. variance


参考答案：C, E

第6题：

Refer to the exhibit. EIGRP has been configured on router D. Router C is performing mutual redistribution between EI GRP and OSPF. While verifying that the redistribution is functioning properly, you discover that while router C has all of the EIGRP routes in its routing table, router A does not have any routes from the EIGRP domain. What on router C may be the cause o f the problem?（）

A. The no auto - summary command needs to be added under router eigrp 1

B. The subnets keyword was not included in the redistribute command under router ospf 1

C. The metric specified for the redistributed EIGRP routes is too large; m aking the EIGRP routes unreachable by router A

D. The default - information originate command needs to be added under router ospf 1

E. The administrative distance of either OSPF or EIGRP must be changed so that EIGRP has a higher administrative distanc e than OSPF


参考答案：B

第7题：

Refer to the exhibit. Which th ree commands should be used on router B1 to redistribute the EIGRP AS 10 routes into RIP?()

A. router rip

B. router eigrp 10

C. redistribute eigrp 10

D. redistribute rip

E. default - metric 10000 100 255 1 1500

F. default - metric 5


参考答案：A, C, F

第8题：

Refer to the exhibit. What must be done on router RTA to ensure that EIGRP works effectively in a Frame Relay multipoint environment?()

A. Issue the command bandwidth 224 on the physical interface.

B. Issue the command bandwidth 56 on the physical interface.

C. Issue the command bandwidth 224 on each subinterface.

D. Issue the command bandwidth 56 on each subinterface.


参考答案：A

第9题：

Refer to the exhibit. OSPF is running throughout the network. You want to minimize the propagation of LSAs into and out of A rea 1. Which OSPF feature would best achieve this goal? ()

A. stub

B. totally stubby

C. NSSA

D. totally NSSA


参考答案：D

第10题：

Refer to the exhibit. When you examine the routing table of R1 and R4, you are not able to see the R1 Ethernet subnet on the R4 routing ta ble. You are also not able to see the R4 Ethernet subnet on the R1 routing table.Which configuration change should be made to resolve this issue? Select the routers where the configuration change will be required, and select the required EIGRP configur ation command(s).（）

A. R1 and R4

B. R2 and R3

C. ip summary-address eigrp 1 10.1.1.0 255.255.255.0 and ip summary - address eigrp 110.2.2.0 255.255.255.0

D. variance 2

E. eigrp stub connected

F. no auto - summary


参考答案：B, F

更多相关问题
相关内容