Access Point R1 is an Aironet 1200 that has been converted f

第1题：

A new Aironet 1200 series AP has been installed in the Company WLAN.  What happens when this  device is connected to the LAN， with a default configuration？（）

• A、 The access point will attempt to download an encryption key from the nearest wireless server.
• B、 The access point makes several attempts to get an IP address from the DHCP server. If the  access point does not receive an address， it assigns itself the IP address 10.0.0.1 for 5 minutes.
• C、 The access point will attempt to connect to the nearest wireless server using LEAP  authentication.
• D、 The access point requests an IP address from the DHCP server. If the access point does not  receive an address， it continues to send requests indefinitely.
• E、 None of the other alternatives apply

第2题：

As the Company wireless administrator， you required to be knowledgeable about the wireless LAN  components.  Which two statements about these components are true？ （）

• A、 In the autonomous access point solution， control is provided by the WLAN controller.
• B、 In the lightweight access point solution， WLAN management is provided by the WLAN Control  System （WCS）.
• C、 In the autonomous access point solution， control is provided by the WDS （Wireless Domain  Services）.
• D、 Cisco Aironet autonomous access points cannot be supported by the Cisco Unified Wireless  Network.
• E、 Ii the lightweight access point solution， WLAN management is provided by the WLAN Solution  Engine （WLSE）.
• F、 Cisco Aironet lightweight access points cannot be supported by the Cisco Unified Wireless  Network.

第3题：

Access Point R1 is an Aironet 1200 that has been converted from autonomous mode to LWAPP  mode. After this conversion， which two statements are true？ （）

• A、 LWAPP-enabled access points can still communicate with Wireless Domain Services （WDS）  devices.
• B、 An LWAPP-enabled access point console port provides read-only access to the unit.
• C、 LWAPP-enabled access points support Layer 2 LWAPP.
• D、 LWAPP-enabled access points must get an IP address and discover the controller using  DHCP， DNS， or an IP subnet broadcast.
• E、 An LWAPP-enabled access point console port provides read-write access to the unit.

第4题：

A Cisco Aironet 1020 controller-based access point has been connected to a Catalyst 3550-24PWR Switch. However， when it is powered up， the access point fails. What has caused this problem？（）

• A、access point does not support 802.11h
• B、incorrect switch power supply
• C、switch port is not enabled
• D、switch does not support 802.3af
• E、access point has not been initialized with the primary controller

第5题：

A customer has deployed a wireless core feature set using autonomous access points and now wants to include a satellite building 4500 feet away from the main campus. The customer also wants to provide wireless access to a courtyard for wireless clients in close proximity to the antenna mounting position. Which Cisco Aironet product is the most applicable solution？（）

• A、 Cisco Aironet 1000 Series
• B、 Cisco Aironet 1100 Series
• C、 Cisco Aironet 1200 Series
• D、 Cisco Aironet 1300 Series
• E、 Cisco Aironet 1400 Series

第6题：

An reap was supporting 16 wlans， but now it only supports one. What happened to cause the change？（）

• A、controller connectivity has been lost.
• B、the access point lost its configuration.
• C、the access point was rebooted.
• D、an access point firmware upgrade is in progress.

第7题：

On a Cisco Aironet 1240AG Series standalone access point， the radio LED is dark blue and blinking， butthe status LED and Ethernet LED are both off. What does this indicate？（）

• A、A firmware upgrade is in progress.
• B、An access point buffer overflow is occurring.
• C、The internal radio has failed.
• D、The access point is booting.

第8题：

A new lightweight access point （LAP） has been installed in the Company WLAN.  Which two  statements correctly describe the association process between this LAP and a WLAN controller？ （）

• A、 An access point will search for a controller using a broadcast address if using LWAPP Layer 2  and a unicast address if using LWAPP Layer 3 mode.
• B、 If multiple wireless controllers are detected by an access point， the controller with the fewest  associated access points is chosen to associate with.
• C、 In order to associate in Layer 3 mode， the access point must have been preconfigured with an  IP address.
• D、 Once an access point associates with a controller in LWAPP Layer 3 mode， it receives an IP  address from the controller.
• E、 An access point first searches for a controller in LWAPP Layer 2 mode. If the search is not  successful， the access point then attempts to locate a controller in LWAPP Layer 3 mode.
• F、 If multiple wireless controllers are detected by an access point， all of them will be used and  traffic will be load balanced.

第9题：

On a Cisco Aironet 1130AG Series standalone access point， the status LED is dark blue and blinking. What does this indicate？（）

• A、The internal radio has failed.
• B、A firmware upgrade is in progress.
• C、An access point buffer overflow is occurring.
• D、The access point is booting.

第10题：

A Cisco Aironet 1020 controller-based access point has been connected to a Catalyst 3550-24 PWRSwitch. However， when it is powered up， the access point fails. What has caused this problem？（）

• A、access point does not support 802.11h
• B、incorrect switch power supply
• C、switch port is not enabled
• D、switch does not support 802.3af
• E、access point has not been initialized with the primary controller