After adding a new Ethernet card to a system and rebooting， 

第1题：

In the event of a catastrophic disaster， after which you need to replace the entire UCS blade system （that is， new fabric interconnects， new IOMs， new chassis， and new blades）， what type of backup would provide the most complete set of information？（）

• A、 logical configuration
• B、 all configuration
• C、 full state
• D、 system configuration

第2题：

A technician purchases a new 120 GB IDE hard disk to use in an old server as a swap drive. After adding the drive to the server， the technician discovers that the operating system does not detect the drive.   After rebooting the server， the technician notices the drive is missing from POST and comes to the conclusion that the BIOS needs to be updated. The technician downloads the latest version of the BIOS update from the manufacturer website.   Which action should the technician take next？（）

• A、 backup the BIOS configuration to use later
• B、 install the BIOS update from a command prompt
• C、 create a bootable floppy and copy the BIOS update tools to the floppy
• D、 read the manufacturer’s guidelines and recommendations on installing the update

第3题：

第4题：

When installing a new PCIe network card, when should manufacturer software and drivers beinstalled?（）

• A、Before inserting the PCIe network card in the case
• B、After inserting the new PCIe network card in the case
• C、They will be automatically loaded after installation
• D、Load them concurrently with the PCIe network card

第5题：

An administrator replaces the network card in a web server. After replacing the network card some users can access the server but others cannot. Which of the following is the FIRST thing the administrator should check?（）

• A、Default gateway
• B、The ports on the switch
• C、Port security on the server's switch port
• D、Ethernet cable

第6题：

After adding a new Ethernet card to a system and rebooting， the system administrator notices the card was not configured. How can the system administrator determine if there were errors during the configuration process for the card？（）

• A、Examine the bootlog with the command： alog -o -f /var/adm/ras/bootlog
• B、Display the device attributes and errors with the command： lsdev -C -l ent0
• C、Examine the AIX errlog for configuration method errors with the command： errpt -a -C ent0
• D、Examine the ODM for configuration errors with the command： odmget -q "method_errors" ent0

第7题：

An administrator replaces the network card in a web server. After replacing the network card some users can access the server but others cannot.  Which of the following is the FIRST thing the administrator should check？（）

• A、 Default gateway
• B、 The ports on the switch
• C、 Port security on the servers switch port
• D、 Ethernet cable

第8题：

第9题：

Bob, a technician, is adding a secondary IDE hard drive to an older system. After installation and the first boot, the drive is not showing in Disk Management. Which of the following is the MOST likely cause of the issue?（）

• A、The new drive’s jumper is set for master.
• B、The new drive is connected to the secondary bus as a slave drive.
• C、Both drives’ jumpers are set for cable select.
• D、The old drive’s jumper is set for master and the new drive is set for slave.

第10题：

A technician installs a SATA controller card and moves the hard drive cable from the system board to the SATA controller. The system POSTs and the controller BIOS recognizes the hard drive but does not boot to the hard drive and start Windows. Which of the following is the MOST likely cause of the problem？（）

• A、Windows cannot be booted from a controller card.
• B、The hard drive must have Windows reinstalled because a new controller card was installed.
• C、The SATA controller card was not set as a boot device in the computer BIOS.
• D、The new controller must have the correct jumper settings for Windows mode.