单选题A server has been having a memory problem. What feature can be used to determine the failing memory module？（）A Reboot the serverB RSA IIC LightPath DiagnosticsD ServerGuide

第1题：

After applying a new ACL on a device， its CPU utilization rose significantly and many messages startingwith "%SEC-6-IPACCESSLOG" appeared on the Syslog server.What can be done to resolve this situation？（）

• A、Increase memory allocation for ACLs.
• B、Remove all entries from the ACL and use a single permit ip any any statement.
• C、Remove the log keyword from each ACL entry.
• D、Reboot the device after the ACL has been applied.

第2题：

A technician has to populate a server motherboard with memory. The board has a memory bus speed of 800 MHz. Which of the following memory types should be used？（）

• A、DDR3
• B、SDRAM
• C、DDR
• D、DDR2

第3题：

第4题：

A customer is trying to remotely upgrade their system BIOS firmware on their xSeries server through their RSA adapter.  What feature would best fit the requirement？（）

• A、Use the remote update feature of the RSA
• B、Use the remote diskette/CD feature on the RSA
• C、Insert the diskette in the server， flash the BIOS， and reboot the server.
• D、Use the remote POST function of the RSA to flash the BIOS

第5题：

The technician is repairing a PC which appears to have a failing RAM module. After replacing the module, the extra memory still is not registering. Which of the following is MOST likely the issue?（）

• A、Jumper settings are incorrect
• B、The RAM module is defective
• C、The memory slot is defective
• D、CMOS needs to be flashed

第6题：

AIX 5L and SUN Solaris have differing approaches at handling processor failures. Which statement best describes how AIX handles processor failures？（）

• A、If AIX discovers a processor with too many recoverable errors during runtime， it will dynamically turn off that processor， while the rest of the system keeps running.
• B、If AIX detects a failing processor it will automatically move all resources to another processor. The failed processor can be hot-swapped and the new replacement becomes the active processor.
• C、If AIX determines a processor is failing， it will perform diagnostics to determine which processor function can be disabled and dynamically reallocate all CPU and memory resources thus isolating the failure condition and preventing a reboot.
• D、If AIX senses a processor level error condition， internal diagnostics are activated to determine the severity of the problem. After the failure threshold is met， a message is broadcast to the service processor informing the operator to perform a system reboot.

第7题：

Which of the following does an out-of-memory error indicate on a printer?（）

• A、A faulty memory module in the printer.
• B、A postscript print job has been sent to the printer.
• C、A large print job has been sent to the printer.
• D、The printer firmware needs to be updated.

第8题：

When enabling IPS on an ISR using the Cisco SDM IPS Wizard， in what location can the SDF be placed？（）

• A、On the RAM of the ISR
• B、On the USB memory stick of the ISR
• C、On the NVRAM of the ISR
• D、On the IPS Module of the ISR
• E、On the Flash memory of the ISR

第9题：

The administrator has just installed a new memory module into the server. Now， the server is not showing the new memory. Which of the following should the administrator perform FIRST？（）

• A、System reboot
• B、Reseat the memory
• C、Install the latest firmware
• D、Install the latest driver

第10题：

After purchasing the Active Memory Expansion （AME） Enablement Feature，what tasks must be completed before AME can be used？（）

• A、Enable using active partition properties with DLPAR
• B、Enter the activation key via the AIX 6.1 command line and reboot AIX
• C、Enter the activation key via the HMC,power cycle the managed system and start the LPAR
• D、Enter the activation key via the HMC,modify the partition profile and restart the LPAR