Router R1 connects to Router R2 over an Ethernet LAN with both routers using their F0／0 in

Refer to the exhibit. Routers R1 and R2 have established a neighbor relationship and are exchanging routing information. The network design requires that R1 r eceive routing updates from R2, but not advertise any routes to R2. Which configuration command sequence will successfully accomplish this task? （）

A. R1(config)# router eigrp 1 R1(config - router)# passive - interface serial 0

B. R1(config)# access - list 2 0 deny any R1(config)# router eigrp 1 R1(config - router)# distribute - list 20 out serial 0

C. R2(config)# access - list 20 permit any R2(config)# router eigrp 1 R2(config - router)# distribute - list 20 in serial 0

D. R1(config)# access - list 20 permit any R 1(config)# router eigrp 1 R1(config - router)# distribute - list 20 in serial 0

E. R2(config)# access - list 20 deny any R2(config)# router eigrp 1 R2(config - router)# distribute - list 20 out serial 0

F. R2(config)# router eigrp 1 R2(config - router)# passive - interface serial 0

Refer to the exhibit. You have completed an OSPF implementation, and you are verifying OSPF operation. You notice that router A and router B are stuck in the two - way state. From the show ip ospf interface command output, what is the cause of this issue?（）

A. All OSPF implementations must have at le ast one interface in area 0.

B. You are attempting to run in the broadcast mode over an NBMA interface.

C. Both routers are configured to function as a BDR; therefore, there is no DR router.

D. Someone has changed the OSPF router ID; therefore you must clear the OSPF process.

E. The OSPF priority is set to 0 on both routers; therefore neither can become the DR.

There are three routers on a Gigabit Ethernet LAN: Router A, Router B, and Router C. Router A is the Designated Intermediate System (DIS) at Level 1 for that LAN. Router A‘s DIS priority is 64. The LAN is a Level 1-only link. Router D has just been powered up on that same LAN and its DIS priority is 80.Which statement is true?（）

A. Router A remains the DIS and generates a new pseudonode LSP for that LAN

B. Router A remains the DIS and NO new pseudonode LSP is generated for that LAN

C. Router D becomes the new DIS, generates a new pseudonode LSP for that LAN, and purges the old pseudonode LSP generated by Router A

D. Router D becomes the new DIS, does NOT generate a new pseudonode LSP for that LAN, and does NOT purge the old pseudonode LSP generated by Router A

A. Dev - 1 is the DR because it has a lower OSPF router ID

B. Dev - 3 is the DR because it has a higher OSPF router priority

C. Both Dev - 1 and Dev - 3 are using the def ault OSPF router priority

D. Dev - 3 is the DR because it has a lower OSPF router ID

E. Dev - 1 is the DR because it has a higher OSPF router priority

Refer to the exhibit. All routers have Protocol Independent Multicast (PIM) enabled interfaces. On the basis of the configuration provided on routers R1 and R2, which router will take on the func tion of rendezvous point (RP) for the multicast network? （）

A. both routers R1 and R2

B. router R1

C. router R2

D. none of the routers since they are not configured with static RP

Refer to the exhibit. OSPF has been configured on all routers in the network. However, router R1 does not receive a default route to router R2 as in tended. Which configuration change would ensure that R1 would receive a default route from R2? （）

A. Add the area 1 stub command on routers R1.

B. Add the always keyword to the default - information originate configuration command on router R2.

C. Remov e the default information originate configuration command from router R2 and place it on router R1.

D. Add the ip route 5.0.0.0 255.255.255.0 0.0.0.0 command to router R2.

A. Router R1 will only establish full adjacency with the DR and BDR on broadcast multi- access networks.

B. Router R2 has been elected as a DR for the broadcast multiaccess network in OSPF area 1.

C. Routers R1 and R2 are configured as stub routers for OSPF area 1 and OSPF area 2.

D. Router R1 and R2 are configured for a virtual link between OSPF area 1 and OSPF area 2.

E. The Hello parameters on routers R1 and R2 do not m atch.

Router R1, a branch router, connects to the Internet using DSL. Some traffic flows through a GRE and IPsec tunnel, over the DSL connection, destined for an Enterprise network.Which of the following answers best describes the router‘s logic that tells the router, for a given packet, to apply GRE encapsulation to the packet?（）

A. When the packet received on the LAN interface is permitted by the ACL listed on the tunnel greacl command under the incoming interface

B. When routing the packet, matching a route whose outgoing interface is the GRE tunnel interface

C. When routing the packet, matching a route whose outgoing interface is the IPsec tunnel interface

D. When permitted by an ACL that was referenced in the associated crypto map

A. All BGP updates that are received on router R 2 will be sent to routers R3 and R4. Routers R3 and R4 will then forward those BGP updates to router R5

B. None of the BGP updates that are received on router R2 will ever be received by router R5

C. All BGP updates that are received on router R2 will not be sent to routers R3 and R4

D. All BGP updates that are received on router R2 will be sent directly to router R5

A. Both outgoing and incoming routing updates on R1 will be permitted because the d istribute - list 20 out Serial0/0 command cannot be used with association with the outgoing interface.

B. All incoming routing updates from R2 will be suppressed, but the outgoing updates will continue to be sent.

C. Both outgoing and incoming routing up dates on R1 will be stopped because of the passive - interface Serial0/0 configuration statement.

D. All outgoing routing updates from router R1 to router R2 will be suppressed, but the inbound updates will continue to be received.