Router R1 has the following configuration. Assuming R1‘s F0/0 interface has a MAC address

题目

Router R1 has the following configuration. Assuming R1‘s F0/0 interface has a MAC address of 0200.0011.1111, what IPv6 addresses will R1 list for interface F0/0 in the output of the show ipv6 interface brief command?()interface f0/0ipv6 address 2345:0:0:8::1/64

A. 2345:0:0:8::1

B. 2345:0:0:8:0:FF:FE11:1111

C. FE80::8:0:FF:FE11:1111

D. FE80:0:0:8::1

如果没有搜索结果或未解决您的问题,请直接 联系老师 获取答案。
相似问题和答案

第1题:

Refer to the exhibit. Router R1 is being used as a relay device for autoconfiguration of switch S1.Which configuration will acc omplish this? ()

A.S1(config)# interface fastethernet 0/1S1(config - if)# ip helper - address 10.0.0.2

B.S1(config)# interface fastethernet 0/1 S1(config - if)# ip helper - address 20.0.0.1

C.R1(config)# interface fastethernet 0/0 R1(config - if)# ip help er - address 20.0.0.2R 1(config - if)# ip helper - address 20.0.0.3 R1(config - if)# ip helper - address 20.0.0.4 R1(config - if)# exit R1(config)# interface fastethernet 0/1 R1(config - if)# ip helper - address 10.0.0.1

D.R1(config)# interface fastethernet 0/0 R1 (config - if)# ip helper - address 20.0.0.1 R2(config)# interface fastethernet 0/0 R2(config - if)# ip helper - address 20.0.0.1 R3(config)# interface fastethernet 0/0 R3(config - if)# ip helper - address 20.0.0.1 R4(config)# interface fastethernet 0/0 R4(config - if)# ip helper - address 20.0.0.1

E.S1(config)# interface fastethernet 0/1 S1(config - if)# ip helper - address 10.0.0.2 R2(config)# interface fastethernet 0/0 R2(config - if)# ip helper - address 20.0.0.1 R3(config)# interface fastethernet 0/0 R3(config - if) # ip helper - address 20.0.0.1 R4(config)# interface fastethernet 0/0 R4(config - if)# ip helper - address 20.0.0.1


参考答案:C

第2题:

Host 1 sends a request for a file to remote sever1. Which destination address does Host 1 place f the packet containing the request()。

  • A、The Mac address of the NIC in Sever1
  • B、The IP address of Server 1.
  • C、The MAC address of the s0/0/0 interface of router R2
  • D、The IP address of the s0/0/0 interface of router R1
  • E、The IP address of the Fa0/0 interface of router R1

正确答案:B

第3题:

Router R1 has been conf igured with an ipv6 route 2000::/64 S0/0/0 64 command.Which of the following does the 64 at the end of the command represent?()

A. Metric

B. Administrative distance

C. Timeout (seconds)

D. Prefix length

E. Interface ID


参考答案:B

第4题:

On router R1, which three of the following protocols will be forwarded to a host specified by the "iphelper-address" interface configuration command if the configuration has not been modified by the"ip forward-protocol udp" global configuration command?()

  • A、BOOTP
  • B、TFTP
  • C、ARP
  • D、DNS
  • E、proxy-ARP
  • F、FTP
  • G、CDP

正确答案:A,B,D

第5题:

You administer a network that uses two routers, R1 and R2, configured as an HSRP group to  provide redundancy for the gateway. Router R1 is the active router and has been configured as  follows:   R1#configure terminal   R1(config)#interface fa0/0   R1(config-if)#ip address 10.10.0.5 255.255.255.0   R1(config-if)#standby 1 priority 150   R1(config-if)#standby preempt delay minimum 50   R1(config-if)#standby 1 track interface fa0/2 15   R1(config-if)#standby 1 ip 10.10.0.20   Which of the following describes the effect the standby preempt delay minimum 50 command will  have on router R1?()

  • A、 The HSRP priority for router R1 will increase to 200.
  • B、 Router R1 will become the standby router if the priority drops below 50.
  • C、 The HSRP priority for router R1 will decrease to 50 points when Fa0/2 goes down.  
  • D、 Router R1 will wait 50 seconds before attempting to preempt the active router.

正确答案:D

第6题:

Refer to the exhibit. EIGRP has been configured on routers R1 and R2. However, R1 does not show R2 as a neighbor and does not accept routing updates from R2.What could be the cause of the problem?()

A. The no auto - summary command has not been issued under the EIGRP process on both routers.

B. Interface E0 on router R1 has not been configured with a secondary IP address of 10.1.2.1/24.

C. EIGRP cannot exchange routing updates with a neighbor‘s router interface that is configured with tw o IP addresses.

D. EIGRP cannot form neighbor relationship and exchange routing updates with a secondary address.


参考答案:D

第7题:

Router R1 has a connected route for 10.1.1.0/24 off interface Fa0/0. Interface Fa0/0 has been enabled for OSPF due to a router ospf 1 and network 10.0.0.0 0.0.0.255 area 0 command. R1 also has EIGRP configured, with the redistribute ospf 1 metric 1000 100 10 1 1500 command configured under EIGRP. Which one of the following is true?()

  • A、R1 will not redistribute 10.1.1.0/24 into EIGRP, because R1 knows it as a connected route and not as an OSPF route.
  • B、For any OS PF routes redistributed into EIGRP, the metric components includea value equivalent to 1 Mbps of bandwidth.
  • C、For any OSPF routes redistributed into EIGRP, the metric components include a value equivalent to 100 microseconds of delay.
  • D、No subnets of network 10.0.0.0 will be redistributed due to the omission of the subnets parameter.

正确答案:B

第8题:

Router R1 lists the following output from a show command. Which of the following is true about R1?()R1 show ip v6 interface f0/0FastEthernet0/0 is up, line protocol is upIPv6 is enabled, link - local address is FE80::213:19FF:FE12:3456No Virtual link - local address(es):Global unicast address(es):2000::4:213:19FF:FE12:3456, subnet is 2000:0:0:4::/64 [EUI]Jo ined group address(es):FF02::1FF02::2FF02::1:FF:12:3456

A. R1‘s solicited node multicast address is FF02::1:FF:12:3456.

B. R1‘s 2000::4:213:19FF:FE12:3456 address is a global unicast with all 128 bits statically configured.

C. Address FF02::2 is R1‘s solicited node multicast.

D. R1‘s solicited node multicast, not listed in this output, would be FF02::213:19FF:FE12:3456.


参考答案:A

第9题:

Host 1 sends an ICMP echo request to remote sever1. Layer2 header of the frame containing the ping packet()。

  • A、The IP address of sever 1.
  • B、The MAC address of NIC in sever 1.
  • C、The IP address of F0/0 interface of router R1.
  • D、The MAC address of the Fa0/0 interface of router R1.
  • E、The IP address of the s0/0/0 interface of router R2
  • F、The MAC address of the s0/0/0 interface of router R2

正确答案:D

第10题:

Router R1, an ASBR connected to the Internet and to backbone area 0, has been configured with a default - information originate command. Which of the following is true about the effects of this configuration command?()

  • A、R1 will always create and flood a default route into the OSPF domain.
  • B、R1 will create and flood an LSA for prefix/length 0.0. 0.0/0 into the OSPF domain if R1's IP routing table has a route to 0.0.0.0/0.
  • C、R1 will set a flag on the LSA for the subnet between itself and one of the ISPs, noting this subnet as a default network, regardless of whether R1 has a default route.
  • D、R1 w ill set a flag on the LSA for the subnet between itself and one of the ISPs, noting this subnet as a default network, but only if R1 has a route to 0.0.0.0/0.

正确答案:B

更多相关问题