Auto
Negotiate
Designate
No negotiate
第1题:
A new trunk has been configured on a switch in the Ezonexam LAN. By default, which VLANs are allowed over this trunk link?
A. No VLANs
B. Only the VLANs that are specified when creating the trunk
C. Only VLANs 1-64
D. All VLANs
E. All VLAN's except VLAN 1
F. None of the above
第2题:
A. All defined VLANs are allowed on the trunk by default.
B. Each VLAN, or VLAN range, that is specified with the switchport mode command.
C. Each VLAN, or VLAN range, that is specified with the vtp domain command.
D. Each VLAN, or VLAN range, that is specified with the vlan database command.
第3题:
A、access vlan vlan-id
B、port link-type trunk
C、port trunk allow-pass vlan
D、set port vlan vlan-id
答:B、C
解析:
(1) 首先我们需要确定我们需要用到的端口模式:
Access介入模式 pc—交换机 Trunk中继链路模式: 交换机—交换机
(2) 其次在两个交换机上各创建vlan5、vlan10的端口,并把pc19与pc21的端口设置为access模式并加入vlan5,把pc20与pc22的端口设置为access模式并加入vlan10,把两个交换机相连接的端口设置为trunk中继链路模式,并把vlan端口加入到中继链路。
(3) 最后,打开计算机,使用ping命令进行查看。
Swich1:
system-view //进入系统试图
[Huawei]vlan batch 5 10 //创建vlan端口
[Huawei]interface ethernet 0/0/1 //进入e0/0/1端口进行配置
[Huawei-Ethernet0/0/1]port link-type access //设置端口的模式为access
[Huawei-Ethernet0/0/1]port default vlan 5 //把端口加入vlan 5
[Huawei-Ethernet0/0/1]interface ethernet 0/0/2 //进入e0/0/2端口进行配置
[Huawei-Ethernet0/0/2]port link-type access //设置端口模式为access
[Huawei-Ethernet0/0/2]port default vlan 10 //把端口加入vlan 5
[Huawei-Ethernet0/0/2]interface ethernet 0/0/3 //进入e0/0/3端口
[Huawei-Ethernet0/0/3]port link-type trunk //设置端口模式为trunk
[Huawei-Ethernet0/0/3]port trunk allow-pass vlan 5 10 //把vlan 5 10加入到中继链路
第4题:
Two Company switches are connected via a trunk link. In this network, the original frame is encapsulated and an additional header is added before the frame is carried over a trunk link. At the receiving end, the header is removed and the frame is forwarded to the assigned VLAN. This describes which technology?()
第5题:
A. to provide a mechanism to dynamically assign vlan membership to switch ports
B. to allow traffic to be carried from multiple vlans over a single link between switches
C. to allow native vlan information to be carried over a trunk link
D. to provide a mechanism to manually assign vlan membership to switch ports
E. to allow for managing the additions,deletions,and changes of vlans between switchs
第6题:
A new switch is being installed in the Ezonexam network and you have been assigned the task of connecting it to an existing switch. In doing this, you want to set up the VLAN Trunking Protocol so that VLAN information can be passed between the switches. Which of the following must you do to accomplish this? (Choose all that apply).
A.You must set each end of the trunk line to IEEE 802.1e encapsulation.
B.You must set the same VTP management domain name on both switches.
C.You must set all ports on the two switches as access ports.
D.You must configure one of the switches as a VTP server.
E.You must use a rollover cable to connect the two switches.
第7题:
VLAN Tagging, also known as Frame Tagging, is a method developed by Cisco to help identify packets travelling through trunk links. When an Ethernet frame traverses a trunk link, a special VLAN tag is added to the frame and sent across the trunk link .How does ERS use the VLAN tag?()
A. provide service internetworking
B. support transparency for Layer 2 frames
C. indicate destination as a connection identifier
D. map to the DLCI in service internetworking
第8题:
A new Ezonexam switch is installed into an existing LAN and a new VTP trunk is set up with an existing switch. Which VLANs will be allowed on this new trunk?
A.All defined VLANs are allowed on the trunk by default.
B.Each VLAN, or VLAN range, that is specified with the switchport mode command.
C.Each VLAN, or VLAN range, that is specified with the vtp domain command.
D.Each VLAN, or VLAN range, that is specified with the vlan database command.
E.None of the above
第9题:
You are the network administrator tasked with designing a switching solution for the Company network. Which of the following statements describing trunk links are INCORRECT?()
第10题:
A new switch is installed into an existing LAN and a new VTP trunk is set up with an existing switch. Which VLANs will be allowed on this new trunk?()