The switch that will share its VLAN configuration must be in VTP server mode.
The switches must be in the same VTP domain.
The switch that will share the VLAN information must be configured as the root bridge.
The switches must be connected over VLAN trunks.
The switches must be configured to use the same STP version.
The switches must have VTP pruning activated.
第1题:
As a network administrator, you issue the interface auto qos voip cisco-phone command on a port in an edge network. It is possible for a Cisco Catalyst switch to check if a Cisco IP Phone is directly attached to that port by:()
A. using DHCP snooping
B. snooping the incoming 802.1Q VLAN tag
C. using CDP
D. snooping the CoS marking on the incoming frames
第2题:
A. Configure the switch to be in VTP client mode.
B. Configure the switch to be in VTP domaint mode.
C. Configure the switch to be in VTP transparent mode.
D. Configure the switch to be in VTPv2.
第3题:
在Cisco Catalyst 3548以太网交换机上建立一个名为lib105的VLAN,下列正确的配置是______。
A) Switch-3548#vlan 1 name lib 105
Switch-3548#exit
B) Switch-3548(vlan)#vlan 1 name lib 105
Switch-3 548(vlan)#exit
C) Switch-3548(vlan)#vlan 1000 name lib 105
Switch3548(vlan)#exit
D) Swimh-3548(vlan)#vlan 1002 name lib 105
Switch-3548(vlan)#exit
A.
B.
C.
D.
第4题:
Which interface commands would you enter on a Catalyst 2900 switch, if your goal was to bring all VLAN traffic to another directly connected switch?()
第5题:
A.This switch has more than one interface connected to the root network segment in VLAN 2.
B.This switch is running RSTP while the elected designated switch is running 802.1d Spanning Tree.
C.This switch interface has a higher path cost to the root bridge than another in the topology.
D.This switch has a lower bridge ID for VLAN 2 than the elected designated switch.
第6题:
A. Switch(config-if)# vlan all
B. Switch(config-if)# switchport trunk encapsulation dot1q
C. Switch(config-if)# switchport access vlan all
D. Switch(config-if)# switchport mode trunk
E. Switch(config-if)# switchport access vlan 303
第7题:
An administrator is unsuccessful in adding VLAN 50 to aswitch. While troubleshooting the problem, the administrator views the output of the show vtp status command, which is displayed in the graphic. What commands must be issued on this switch to add VLAN 50 to the database?()
A. Switch(config-if)# switchport access vlan 50
B. Switch(vlan)# vtp server
C. Switch(config)# config-revision 20
D. Switch(config)# vlan 50 name Tech
E. Switch(vlan)# vlan 50
F. Switch(vlan)# switchport trunk vlan 50
第8题:
The network administrator has just finished installing a new 10/100/1000 switch, but receives reports from the server administrator that servers connected to the new switch seem to be experiencing slow LAN connections. The network administrator checks the port connecting the new switch to the core switch and sees the following information:Which of the following is the MOST likely cause of the slow connections?()
A. The servers have not had VLAN tagging enabled on their NICs.
B. Speed and duplex have not been set.
C. VLAN tagging was not set on the trunk.
D. The servers have been connected with CAT5 cable.
第9题:
A Cisco Catalyst switch is part of the CIS network. As an experienced network administrator, you are thinking of filtering the traffic within VLANI00 with the use of a VACL named "test" on that switch. Which of the following command will enable that?()
第10题:
Which of the following are VLAN frame encapsulation types that may be configured on a Catalyst switch?()