多选题Which three steps are used to configure IPv6 in JUNOS software?（）AAssign 128-bit router id.BEnable a routing instance.CAssign IPv6 addresses to interfaces.DAdd IPv6 family support to interfaces.EEnable IPv6-capable routing protocol.

题目

多选题

Which three steps are used to configure IPv6 in JUNOS software?（）

Assign 128-bit router id.

Enable a routing instance.

Assign IPv6 addresses to interfaces.

Add IPv6 family support to interfaces.

Enable IPv6-capable routing protocol.

如果没有搜索结果或未解决您的问题，请直接联系老师获取答案。

相似问题和答案

第1题：

In JUNOS software, which three routing protocols can be used to route IPv6?()

A. IS-IS

B. Static

C. RIPv2

D. OSPFv2

E. MP-BGP

参考答案：A, B, E

第2题：

Which command must be globally enabled on a Cisco router to support IPv6?()

A. ip routing ipv6

B. ipv6 unicast - routing

C. ipv6 routing

D. ip classless

E. ipv6 cef

参考答案：B

第3题：

You wish to configure IPv6 support on a router which does not have any current IPv4 configuration.Which three steps are used to configure IPv6 with an accompanying IGP in JUNOS software? ()

A. set protocols isis inet6

B. set routing-options router-id router-id

C. set protocols ospf3 area 0 interface all

D. set interface fe-0/0/1 unit 0 family inet6

E. set routing-options ipv6-router-id router-id

参考答案：B, C

第4题：

Which three steps are used to configure IPv6 in JUNOS software？（）

A、Assign 128-bit router ID
B、Enable a routing instance.
C、Assign IPv6 addresses to interfaces.
D、Add IPv6 family support to interfaces

正确答案:A,C,D

第5题：

You wish to configure IPv6 support on a router which does not have any current IPv4 configuration.Which three steps are used to configure IPv6 with an accompanying IGP in JUNOS software? （）

A、set protocols isis inet6
B、set routing-options router-id router-id
C、set protocols ospf3 area 0 interface all
D、set interface fe-0/0/1 unit 0 family inet6
E、set routing-options ipv6-router-id router-id

正确答案:B,C

第6题：

Which of the following IPv6 tunneling mechanisms support IPv6 IGP routing protocols?()

A. Automatic 6to4

B. Manually configured tunnel

C. ISATAP

D. GRE

参考答案：B, D

第7题：

Which three approaches can be used while migrating from an IPV4 addressing scheme to an IPV6 scheme.()

A. statically map IPV4 address to IPV6 addresses

B. configuration IPv4 tunnels between IPV6 islands

C. use DHCPv6 to map IPV4 addresses to IPV6 addresses

D. use proxying and translation to translate IPV6 packets into IPV4 packets

E. configure IPV6 directly

F. enable dual-stack routing

参考答案：A, B, F

第8题：

By default, which JUNOS software routing table contains IPv6 unicast routes?()

A.inet.6

B.ipv6.0

C.inet0

D.inet6.0

参考答案：D

第9题：

Which of the following IPv6 tunneling mechanisms support IPv6 IGP routing protocols?（）

A、Automatic 6to4
B、Manually configured tunnel
C、ISATAP
D、GRE

正确答案:B,D

第10题：

Which two of these steps are minimum requirements to configure OSPFv3 under IPv6？（）

A、Configure a routing process using the command ipv6 router ospf [process-id].
B、Add the network statement for the interfaces on which OSPF will run.
C、Configure OSPF on the interface that it will run on.
D、Use the passive-interface command on the interfaces on which OSPF should not run.
E、Enable routing.

正确答案:C,E

多选题Which three steps are used to configure IPv6 in JUNOS software?（）AAssign 128-bit router id.BEnable a routing instance.CAssign IPv6 addresses to interfaces.DAdd IPv6 family support to interfaces.EEnable IPv6-capable routing protocol.

题目

相似问题和答案

更多相关问题

相关内容